The driver side knee airbag squib circuit consists of the airbag ECU assembly and lower No. 1 instrument panel airbag assembly.
The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1860/64 | Short in Driver Side Knee Airbag Squib Circuit | ·
The airbag ECU assembly detects a line short in the driver side knee airbag squib during the primary check. ·
Driver side knee airbag squib malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly) ·
Airbag ECU assembly |
Applies to check mode |
| B1861/64 | Open in Driver Side Knee Airbag Squib Circuit | ·
The airbag ECU assembly detects an open in the driver side knee airbag squib. ·
Driver side knee airbag squib malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly) ·
Airbag ECU assembly |
Applies to check mode |
| B1862/64 | Short to GND in Driver Side Knee Airbag Squib Circuit | ·
The airbag ECU assembly detects a short to ground in the driver side knee airbag squib. ·
Driver side knee airbag squib malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly) ·
Airbag ECU assembly |
Applies to check mode |
| B1863/64 | Short to B+ in Driver Side Knee Airbag Squib Circuit | ·
The airbag ECU assembly detects a short to B+ in the driver side knee airbag squib. ·
Driver side knee airbag squib malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Driver side knee airbag squib (Lower No. 1 instrument panel airbag assembly) ·
Airbag ECU assembly |
Applies to check mode |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform the simulation method by selecting check mode (Signal Check) using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *A | w/o Passenger Airbag ON/OFF Indicator |
| *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not loose, deformed or damaged.
The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs of the activation prevention mechanism of the instrument panel wire connector are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the airbag ECU assembly.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Lower No. 1 Instrument Panel Airbag Assembly | *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
- | - |
Connect SST (resistance 2.1 Ω) to connector C.
Never connect a tester to the lower No. 1 instrument panel airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.
Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect SST from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel wire from the airbag ECU assembly.
| *A | w/o Passenger Airbag ON/OFF Indicator | *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Lower No. 1 Instrument Panel Airbag Assembly | *2 | Airbag ECU Assembly |
| *3 | Floor Wire | - | - |
| *a | Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly) |
- | - |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F23-1 (DK+) - Body ground | Power switch on (IG) | Below 1 V |
| F23-2 (DK-) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F23-1 (DK+) - F23-2 (DK-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F23-1 (DK+) - Body ground | Always | 1 MΩ or higher |
| F23-2 (DK-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F23-1 (DK+) - F23-2 (DK-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/o Passenger Airbag ON/OFF Indicator |
| *B | w/ Passenger Airbag ON/OFF Indicator |
| *1 | Lower No. 1 Instrument Panel Airbag Assembly |
| *2 | Airbag ECU Assembly |
Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag ECU assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.
Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG