Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1875/67  Short in Passenger Side Front Seat Cushion Squib Circuit  B1876/67  Open in Passenger Side Front Seat Cushion Squib Circuit  B1877/67  Short to GND in Passenger Side Front Seat Cushion Squib Circuit  B1878/67  Short to B+ in Passenger Side Front Seat Cushion Squib Circuit  


DESCRIPTION

The passenger side front seat cushion squib circuit consists of the airbag ECU assembly and front seat cushion airbag assembly RH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the passenger side front seat cushion squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1875/67 Short in Passenger Side Front Seat Cushion Squib Circuit
·

The airbag ECU assembly detects a line short in the passenger side front seat cushion squib circuit during the primary check.

·

Passenger side front seat cushion squib malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Passenger side front seat cushion squib (Front seat cushion airbag assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1876/67 Open in Passenger Side Front Seat Cushion Squib Circuit
·

The airbag ECU assembly detects an open in the passenger side front seat cushion squib circuit.

·

Passenger side front seat cushion squib malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Passenger side front seat cushion squib (Front seat cushion airbag assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1877/67 Short to GND in Passenger Side Front Seat Cushion Squib Circuit
·

The airbag ECU assembly detects a short to ground in the passenger side front seat cushion squib circuit.

·

Passenger side front seat cushion squib malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Passenger side front seat cushion squib (Front seat cushion airbag assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1878/67 Short to B+ in Passenger Side Front Seat Cushion Squib Circuit
·

The airbag ECU assembly detects a short to B+ in the passenger side front seat cushion squib circuit.

·

Passenger side front seat cushion squib malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Passenger side front seat cushion squib (Front seat cushion airbag assembly RH)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C316539E52
0.688,2.656 3.302,3.198 2.615,0.542 10 false Passenger Side Front Seat Cushion Squib (Front Seat Cushion Airbag Assembly RH) 0.688,2.5 1.146,2.698 0.458,0.198 10 false Ms1 4.646,3.167 6.292,3.49 1.646,0.323 10 false Airbag ECU Assembly 4.646,3.01 5.021,3.229 0.375,0.219 10 false M45 4.688,1.167 5.198,1.458 0.51,0.292 10 false FCP+ 4.688,2.01 5.167,2.25 0.479,0.24 10 false FCP- 4.448,1.073 4.823,1.292 0.375,0.219 10 false 12 4.448,1.906 4.823,2.125 0.375,0.219 10 false 11 1.948,1.063 2.458,1.406 0.51,0.344 10 false FCP+ 1.969,1.885 2.469,2.198 0.5,0.313 10 false FCP- 2.406,1.063 2.781,1.281 0.375,0.219 10 false 2 2.406,1.885 2.781,2.104 0.375,0.219 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238348C01
0.531,1.198 0.531,0.688 0.531,0.688 0.708,0.688 false 1.365,1.198 1.365,0.688 1.365,0.688 1.542,0.688 false 0.656,1.188 1.052,1.438 0.396,0.25 10 D 1.031,1.188 1.354,1.427 0.323,0.24 10 C 1.604,1.188 1.938,1.552 0.333,0.365 10 B 1.99,1.188 2.333,1.542 0.344,0.354 10 A 2.438,0.896 2.75,1.208 0.313,0.313 10 *2 0.76,0.604 1.021,0.854 0.26,0.25 10 *1 1.583,0.604 1.854,0.896 0.271,0.292 10 *3
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat cushion airbag assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat cushion airbag assembly RH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT CUSHION AIRBAG ASSEMBLY RH

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT CUSHION AIRBAG ASSEMBLY RH
a.
C249370C10
0.667,2.25 1.063,2.479 0.396,0.229 2.177,2.406 2.385,2.406 false 0.854,0.958 0.854,0.51 0.854,0.51 0.656,0.51 false 0.958,0.948 1.219,1.333 0.26,0.385 10 false D 1.323,0.948 1.563,1.25 0.24,0.302 10 false C 1.823,0.948 2.125,1.396 0.302,0.448 10 false B 1.979,0.948 2.323,1.479 0.344,0.531 10 false A 2.427,0.646 2.781,1.094 0.354,0.448 10 false *2 0.49,0.438 0.875,0.865 0.385,0.427 10 false *1 0.542,1.719 0.906,2.094 0.365,0.375 10 false *a 2.427,2.323 2.875,2.698 0.448,0.375 10 false SST 0.74,2.281 1.052,2.635 0.313,0.354 10 false Ms1
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Cushion Airbag Assembly RH)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat cushion airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.


HINT:

Codes other than DTCs B1875/67, B1876/67, B1877/67 and B1878/67 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C249371C12
0.667,2.167 1.031,2.396 0.365,0.229 0.917,0.99 0.917,0.479 0.917,0.479 0.688,0.479 false 1.625,0.99 1.625,0.479 1.625,0.479 1.406,0.479 false 1.458,2.458 1.146,2.771 false 1.75,2.458 2.063,2.771 false 1.042,0.99 1.688,1.406 0.646,0.417 10 false D 1.354,0.99 1.854,1.448 0.5,0.458 10 false C 1.802,0.99 2.354,1.469 0.552,0.479 10 false B 2.115,0.99 2.531,1.469 0.417,0.479 10 false A 2.521,0.719 2.885,1.167 0.365,0.448 10 false *2 0.521,0.396 1.042,0.771 0.521,0.375 10 false *1 0.417,1.729 0.813,2.031 0.396,0.302 10 false *a 0.969,2.792 1.427,3.094 0.458,0.302 10 false FCP- 1.958,2.792 2.438,3.104 0.479,0.313 10 false FCP+ 1.24,0.396 1.583,0.771 0.344,0.375 10 false *3 0.729,2.198 1.25,2.698 0.521,0.5 10 false Ms1
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Cushion Airbag Assembly RH)


Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ms1-2 (FCP+) - Body ground Power switch on (IG) Below 1 V
Ms1-1 (FCP-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ms1-2 (FCP+) - Ms1-1 (FCP-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ms1-2 (FCP+) - Body ground Always 1 MΩ or higher
Ms1-1 (FCP-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Ms1-2 (FCP+) - Ms1-1 (FCP-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241C01
0.844,1.292 0.844,0.844 0.844,0.844 0.552,0.844 false 0.396,0.781 0.729,1.083 0.333,0.302 10 false *1 0.979,1.302 1.156,1.531 0.177,0.229 10 false D 1.135,1.302 1.344,1.5 0.208,0.198 10 false C 1.583,1.302 1.781,1.5 0.198,0.198 10 false B 1.74,1.302 1.938,1.542 0.198,0.24 10 false A 2.146,1.021 2.438,1.26 0.292,0.24 10 false *2
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the front seat cushion airbag assembly RH and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.


HINT:

Codes other than DTCs B1875/67, B1876/67, B1877/67 and B1878/67 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG