Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag ECU assembly and front seat outer belt assembly RH.

The airbag ECU assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1900/73 Short in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly detects a line short in the front pretensioner squib RH circuit during the primary check.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front pretensioner squib RH (Front seat outer belt assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1901/73 Open in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly detects an open in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front pretensioner squib RH (Front seat outer belt assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1902/73 Short to GND in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly detects a short to ground in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front pretensioner squib RH (Front seat outer belt assembly RH)

·

Airbag ECU assembly


Applies to check mode
B1903/73 Short to B+ in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly detects a short to B+ in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Front pretensioner squib RH (Front seat outer belt assembly RH)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C323678E20
2.146,1.063 2.656,1.302 0.51,0.24 10 false R+ 2.167,1.896 2.677,2.135 0.51,0.24 10 false R- 4.688,2.01 5.198,2.25 0.51,0.24 10 false PR- 4.688,1.177 5.198,1.417 0.51,0.24 10 false PR+ 2.406,1.063 2.708,1.448 0.302,0.385 10 false 1 2.406,1.896 2.719,2.26 0.313,0.365 10 false 2 4.531,1.073 4.729,1.302 0.198,0.229 10 false 4 4.104,1.896 4.74,2.115 0.635,0.219 10 false 5*1, 3*2 0.708,2.5 1.219,2.74 0.51,0.24 10 false M49 0.708,2.656 2.979,3.104 2.271,0.448 10 false Front Pretensioner Squib RH (Front Seat Outer Belt Assembly RH) 4.667,3.021 6.188,3.271 1.521,0.25 10 false M44*1, M45*2 4.667,3.177 6.594,3.521 1.927,0.344 10 false Airbag ECU Assembly 0.219,3.531 3.24,3.792 3.021,0.26 10 false *2: w/ Passenger Airbag ON/OFF Indicator 0.219,3.271 3.24,3.531 3.021,0.26 10 false *1: w/o Passenger Airbag ON/OFF Indicator

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238348C01
0.531,1.198 0.531,0.688 0.531,0.688 0.708,0.688 false 1.365,1.198 1.365,0.688 1.365,0.688 1.542,0.688 false 0.656,1.188 1.052,1.438 0.396,0.25 10 D 1.031,1.188 1.354,1.427 0.323,0.24 10 C 1.604,1.188 1.938,1.552 0.333,0.365 10 B 1.99,1.188 2.333,1.542 0.344,0.354 10 A 2.438,0.896 2.75,1.208 0.313,0.313 10 *2 0.76,0.604 1.021,0.854 0.26,0.25 10 *1 1.583,0.604 1.854,0.896 0.271,0.292 10 *3
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly RH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly RH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.
C238358C26
0.458,2.25 0.833,2.5 0.375,0.25 1.792,2.344 1.969,2.344 false 0.708,0.958 0.708,0.51 0.708,0.51 0.552,0.51 false 0.385,0.438 0.875,0.844 0.49,0.406 10 false *1 2.281,0.656 2.76,1.073 0.479,0.417 10 false *2 1.823,0.938 2.208,1.458 0.385,0.521 10 false A 1.677,0.938 2.167,1.417 0.49,0.479 10 false B 1.167,0.948 1.917,1.448 0.75,0.5 10 false C 0.823,0.948 1.604,1.344 0.781,0.396 10 false D 2.01,2.26 2.448,2.594 0.438,0.333 10 false SST 0.302,1.896 0.698,2.26 0.396,0.365 10 false *a 0.521,2.292 0.969,2.76 0.448,0.469 10 false M49
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C237240C58
0.583,2.167 0.958,2.417 0.375,0.25 1.604,2.26 1.875,1.906 false 1.135,1.927 1.417,2.26 false 0.698,1.052 0.698,0.635 0.698,0.635 0.542,0.635 false 1.396,1.052 1.396,0.635 1.396,0.635 1.24,0.635 false 0.375,0.552 0.844,0.948 0.469,0.396 10 false *1 2.271,0.76 2.604,1.135 0.333,0.375 10 false *2 1.885,1.042 2.313,1.5 0.427,0.458 10 false A 1.583,1.042 1.99,1.635 0.406,0.594 10 false B 1.125,1.042 1.542,1.552 0.417,0.51 10 false C 0.823,1.042 1.24,1.427 0.417,0.385 10 false D 1.917,1.833 2.26,2.177 0.344,0.344 10 false R- 0.927,1.833 1.417,2.177 0.49,0.344 10 false R+ 0.26,1.813 0.563,2.188 0.302,0.375 10 false *a 1.073,0.563 1.667,1.063 0.594,0.5 10 false *3 0.646,2.208 1.042,2.542 0.396,0.333 10 false M49
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Disconnect the floor wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M49-1 (R+) - Body ground Power switch on (IG) Below 1 V
M49-2 (R-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (R+) - M49-2 (R-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (R+) - Body ground Always 1 MΩ or higher
M49-2 (R-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (R+) - M49-2 (R-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241C01
0.844,1.292 0.844,0.844 0.844,0.844 0.552,0.844 false 0.396,0.781 0.729,1.083 0.333,0.302 10 false *1 0.979,1.302 1.156,1.531 0.177,0.229 10 false D 1.135,1.302 1.344,1.5 0.208,0.198 10 false C 1.583,1.302 1.781,1.5 0.198,0.198 10 false B 1.74,1.302 1.938,1.542 0.198,0.24 10 false A 2.146,1.021 2.438,1.26 0.292,0.24 10 false *2
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG