Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225221 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1771  Passenger Side Buckle Switch Circuit Malfunction  


DESCRIPTION

The passenger side buckle switch circuit consists of the occupant detection ECU and passenger side buckle switch (front seat inner belt assembly RH).

DTC B1771 is stored when a malfunction is detected in the passenger side buckle switch circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1771 Passenger Side Buckle Switch Circuit Malfunction
·

The occupant detection ECU detects a line short, short to ground or B+, or an open in the passenger side buckle switch circuit.

·

Passenger side buckle switch malfunction

·

Occupant detection ECU malfunction


·

Front seat wire RH

·

Passenger side buckle switch (Front seat inner belt assembly RH)

·

Occupant detection ECU



WIRING DIAGRAM

C240591E17
0.542,3.073 2.885,3.552 2.344,0.479 10 false Passenger Side Buckle Switch (Front Seat Inner Belt Assembly RH) 5.344,3.073 7.052,3.448 1.708,0.375 10 false Occupant Detection ECU 5.344,2.906 5.802,3.188 0.458,0.281 10 false a11 5.219,0.813 5.563,1.281 0.344,0.469 10 false 7 5.219,1.979 5.51,2.25 0.292,0.271 10 false 9 5.396,0.906 6.052,1.542 0.656,0.635 10 false BSW 5.396,2.083 6.073,2.635 0.677,0.552 10 false BGND 1.844,0.813 2.188,1.26 0.344,0.448 10 false 1 1.844,1.979 2.625,2.469 0.781,0.49 10 false 2 1.635,0.906 2.146,1.292 0.51,0.385 10 false + 1.656,2.063 2.167,2.427 0.51,0.365 10 false - 0.542,2.906 0.938,3.167 0.396,0.26 10 false a12

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.

·

If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

·

In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)

NG

REPLACE FRONT SEAT WIRE RH

2.CHECK FRONT SEAT WIRE RH (SHORT TO B+)
a.
C290336C06
0.74,2.177 1.073,2.406 0.333,0.229 2.031,2.385 2.406,2.917 false 1.781,2.385 1.375,2.906 false 1.448,0.219 1.615,0.219 1.615,0.219 1.615,0.719 false 0.688,0.708 1.083,0.948 0.396,0.24 10 false *1 2.5,0.563 2.896,0.979 0.396,0.417 10 false *2 1.292,0.146 1.688,0.396 0.396,0.25 10 false *3 0.573,1.604 0.99,1.938 0.417,0.333 10 false *a 0.813,2.208 1.208,2.448 0.396,0.24 10 false a11 1.208,2.927 1.604,3.167 0.396,0.24 10 false BSW 2.167,0.708 2.563,1.125 0.396,0.417 10 false A 1.885,0.719 2.281,1.135 0.396,0.417 10 false B 1.271,0.719 1.667,1.135 0.396,0.417 10 false C 0.99,0.719 1.385,1.135 0.396,0.417 10 false D 2.229,2.927 2.802,3.177 0.573,0.25 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a11-7 (BSW) - Body ground Power switch on (IG) Below 1 V
a11-9 (BGND) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SEAT WIRE RH (OPEN)

NG

REPLACE FRONT SEAT WIRE RH

3.CHECK FRONT SEAT WIRE RH (OPEN)
a.
C290337C07
0.375,3.458 0.708,3.688 0.333,0.229 0.958,0.635 1.281,0.865 0.323,0.229 1.917,0.823 1.583,1.365 false 1.417,1.927 1.583,1.927 1.583,1.927 1.583,2.344 false 1.719,4.167 2.135,4.167 false 0.917,3.167 1.188,3.5 false 1.531,3.5 1.792,3.167 false 2.167,0.823 2.51,1.354 false 0.667,2.323 1.063,2.646 0.396,0.323 10 false *1 2.479,2.177 2.875,2.5 0.396,0.323 10 false *2 1.271,1.854 1.583,2.104 0.313,0.25 10 false *3 2.156,4.094 2.552,4.344 0.396,0.25 10 false *4 0.823,0.177 1.24,0.677 0.417,0.5 10 false *a 0.167,3.01 0.5,3.333 0.333,0.323 10 false *b 2.146,2.344 2.542,2.667 0.396,0.323 10 false A 1.865,2.344 2.26,2.667 0.396,0.323 10 false B 1.24,2.344 1.635,2.667 0.396,0.323 10 false C 0.958,2.333 1.354,2.656 0.396,0.323 10 false D 0.813,3.073 1.396,3.302 0.583,0.229 10 false - 1.844,3.083 2.281,3.323 0.438,0.24 10 false + 1.417,1.365 1.833,1.865 0.417,0.5 10 false BSW 0.448,3.49 0.844,3.74 0.396,0.25 10 false a12 1.021,0.667 1.417,0.917 0.396,0.25 10 false a11 2.323,1.365 2.823,1.844 0.5,0.479 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*4 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Using a service wire, connect terminals 1 (+) and 2 (-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a11-7 (BSW) - a11-9 (BGND) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

4.CHECK FRONT SEAT WIRE RH (SHORT)

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH (SHORT)
a.
C290336C06
0.74,2.177 1.073,2.406 0.333,0.229 2.031,2.385 2.406,2.917 false 1.781,2.385 1.375,2.906 false 1.448,0.219 1.615,0.219 1.615,0.219 1.615,0.719 false 0.688,0.708 1.083,0.948 0.396,0.24 10 false *1 2.5,0.563 2.896,0.979 0.396,0.417 10 false *2 1.292,0.146 1.688,0.396 0.396,0.25 10 false *3 0.573,1.604 0.99,1.938 0.417,0.333 10 false *a 0.813,2.208 1.208,2.448 0.396,0.24 10 false a11 1.208,2.927 1.604,3.167 0.396,0.24 10 false BSW 2.167,0.708 2.563,1.125 0.396,0.417 10 false A 1.885,0.719 2.281,1.135 0.396,0.417 10 false B 1.271,0.719 1.667,1.135 0.396,0.417 10 false C 0.99,0.719 1.385,1.135 0.396,0.417 10 false D 2.229,2.927 2.802,3.177 0.573,0.25 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a11-7 (BSW) - a11-9 (BGND) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND)
a.
C290336C06
0.74,2.177 1.073,2.406 0.333,0.229 2.031,2.385 2.406,2.917 false 1.781,2.385 1.375,2.906 false 1.448,0.219 1.615,0.219 1.615,0.219 1.615,0.719 false 0.688,0.708 1.083,0.948 0.396,0.24 10 false *1 2.5,0.563 2.896,0.979 0.396,0.417 10 false *2 1.292,0.146 1.688,0.396 0.396,0.25 10 false *3 0.573,1.604 0.99,1.938 0.417,0.333 10 false *a 0.813,2.208 1.208,2.448 0.396,0.24 10 false a11 1.208,2.927 1.604,3.167 0.396,0.24 10 false BSW 2.167,0.708 2.563,1.125 0.396,0.417 10 false A 1.885,0.719 2.281,1.135 0.396,0.417 10 false B 1.271,0.719 1.667,1.135 0.396,0.417 10 false C 0.99,0.719 1.385,1.135 0.396,0.417 10 false D 2.229,2.927 2.802,3.177 0.573,0.25 10 false BGND
*1 Front Seat Inner Belt Assembly RH
*2 Occupant Detection ECU
*3 Front Seat Wire RH
*a Front view of wire harness connector
(to Occupant Detection ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a11-7 (BSW) - Body ground Always 1 MΩ or higher
a11-9 (BGND) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE FRONT SEAT WIRE RH

6.CHECK DTC
a.

Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

d.

Clear the DTCs stored in the airbag ECU assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 10 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


Result:
Proceed to
OK
NG



OK

NG

7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Replace the front seat inner belt assembly RH with a known good one.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 394

e.

Clear the DTCs stored in the airbag ECU assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 10 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 394
OK:

DTC B1771 is not output.


HINT:

Codes other than DTC B1771 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Restore the front seat inner belt assembly RH that was installed for testing to its original location.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

8.REPLACE OCCUPANT DETECTION ECU
8.REPLACE OCCUPANT DETECTION ECU
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Replace the occupant detection ECU with a new one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Result:
Proceed to
NEXT



NEXT

9.PERFORM ZERO POINT CALIBRATION
9.PERFORM ZERO POINT CALIBRATION
a.

Using the GTS, perform Zero Point Calibration.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Body Electrical > Occupant Detection > Utility
Tester Display
Zero Point Calibration
50005 394 4435

Result:
Proceed to
NEXT



NEXT

END