Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225222 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value such as DTC B1801, C1231 and C1433 will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


a.
B428427C02
0.771,0.563 1.365,0.563 true 0.74,1.146 1.229,1.146 1.229,1.146 1.229,0.979 true 0.573,1.052 0.885,1.208 0.313,0.156 10 false *a 0.635,0.479 0.948,0.635 0.313,0.156 10 false A
*a Flat Cable


Check if the spiral cable sub-assembly is centered.

HINT:

When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



b.

If the spiral cable sub-assembly is not centered, center it.

i.
B428428C02
1.74,1.323 1.74,1.917 true 1.667,1.927 1.927,2.135 0.26,0.208 10 false *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.




ii.
B428429C02
0.719,0.771 1.24,0.771 1.24,0.771 1.24,1.021 true 0.688,1.833 1.208,1.833 1.208,1.833 1.208,1.49 true 1.104,1.583 1.104,1.833 true 1.719,1.354 1.719,1.906 true 0.552,0.708 0.865,0.865 0.313,0.156 10 false *a 1.646,1.927 1.958,2.083 0.313,0.156 10 false *b 0.521,1.76 0.833,1.917 0.313,0.156 10 false *c
*a Flat Cable
*b Interlock
*c Alignment Mark


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the alignment marks are aligned and the flat cable shown in the illustration is visible.

HINT:

The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.




Hide 84306 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.
B279789C06
2.25,0.615 1.938,0.49 true 2.313,0.771 1.979,1.063 1.979,1.063 2.344,1.156 true 2.917,0.854 3.156,0.635 true 0.51,0.917 0.302,0.594 true 1.781,0.406 2.094,0.563 0.313,0.156 10 false *c 1.823,1 2.135,1.156 0.313,0.156 10 false *a 3.177,0.552 3.406,0.698 0.229,0.146 10 false *b 0.146,0.5 0.375,0.646 0.229,0.146 10 false *b
*a Guide
*b Pin
*c Lock Pin


Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

NOTICE:
·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

·

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.




b.
C238437

Remove the lock pin from the steering sensor.


Hide 84307 3.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the front wheels are aligned facing straight ahead.


d.

Engage the 3 claws to install the spiral cable with sensor sub-assembly.


e.

Connect each connector.


Hide 45286B 4.INSTALL UPPER STEERING COLUMN COVER

Hide 45024 5.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

Hide 6. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 7.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:

Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B432309C02
0.833,0.656 1.417,0.656 1.417,0.656 1.417,0.875 true 0.677,0.281 1.26,0.281 1.26,0.281 1.51,0.563 true 0.615,0.573 0.823,0.802 0.208,0.229 10 true *a 0.531,0.198 0.677,0.396 0.146,0.198 10 true A
*a Flat Cable


Check if the spiral cable with sensor sub-assembly is centered.

HINT:

When the spiral cable with sensor sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



d.

If the spiral cable with sensor sub-assembly is not centered, center it.

i.
B432310C01
0.813,0.969 1.573,0.969 true 0.615,0.885 0.823,1.073 0.208,0.188 10 true *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.




ii.
B432311C01
0.896,0.281 1.188,0.281 1.188,0.281 1.531,0.563 true 0.792,0.667 1.417,0.667 1.417,0.667 1.417,0.875 true 1.635,1.052 1.469,1.323 1.469,1.323 1.469,1.802 true 1.385,1.823 1.615,2 0.229,0.177 10 true *a 0.604,0.583 0.823,0.802 0.219,0.219 10 true *b 0.729,0.208 0.906,0.406 0.177,0.198 10 true A
*a Interlock
*b Flat Cable


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to the position where the part (A) is positioned at the top and the flat cable shown in the illustration is visible.

HINT:

The spiral cable with sensor sub-assembly can be rotated approximately 2.5 times to both the left and right from the center.




Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY