Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3210E _55 Steering _047548 STEERING COLUMN _0242570 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.INSTALL STEERING COLUMN ASSEMBLY (for RHD)

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.
C345182

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each clamp to the steering column assembly.


c.
C345181

Engage the clamp.


d.

Connect the 2 connectors.


Hide 3.INSTALL STEERING COLUMN ASSEMBLY (for LHD)

a.
C346848

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each clamp to the steering column assembly.


c.
C346847

Engage the clamp.


d.

Connect the 2 connectors.


Hide 45260 4.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C346846C01
0.385,0.542 1.323,0.542 1.323,0.542 1.323,0.802 true 1.229,0.76 1.229,0.552 true 0.219,0.448 0.396,0.667 0.177,0.219 10 true *a
*a Matchmark
V113147

Install in this direction


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Install the No. 2 steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45260 5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C346844C01
1.771,1.25 2.177,1.25 2.177,1.25 2.177,1.792 true 1.792,1.302 2.177,1.302 true 2.104,1.792 2.323,2.021 0.219,0.229 10 true *a
*a Matchmark
V113147

Connect in this direction


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Connect the No. 2 steering intermediate shaft assembly to the steering gear assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45259A 6.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.
C346865

Engage the 2 claws to install the column hole cover silencer sheet.


b.
C346841

Engage the claw to close the column hole cover silencer sheet.


Hide 84340 7.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 87211A 8.INSTALL NO. 2 AIR DUCT (for RHD)

a.
C345180

Engage the 3 claws to install a new No. 2 air duct.


b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55362C 9.INSTALL PARKING BRAKE MOUNTING BRACKET (for RHD)

a.
C345179C01
1.448,0.885 2.156,0.885 true 1.917,1.292 2.771,1.292 true 2.188,0.813 2.5,0.969 0.313,0.156 10 true *a 2.813,1.229 3.125,1.385 0.313,0.156 10 true *b
*a Bolt
*b Screw


Install the parking brake mounting bracket with the bolt and screw.

Torque:
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 87211 10.INSTALL NO. 1 AIR DUCT (for LHD)

a.
C346839

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 58816C 11.INSTALL FRONT NO. 1 CONSOLE BOX INSERT

Hide 55406B 12.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 13.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 73900 14.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 15.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the auxiliary battery connected and the power switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C346838

Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.


b.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 16.INSTALL UPPER STEERING COLUMN COVER

a.
C346836

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C346835

Engage the claw to install the upper steering column cover.


Hide 45024 17.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

If the lower steering column cover sub-assembly is installed in the incorrect order, the parts may break.


a.
C346879C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws as shown in the illustration.


b.
C346880

Engage the 2 claws.


c.
C346833

Install the 2 screws.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 18.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 19.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 20.INSTALL STEERING WHEEL ASSEMBLY

Hide 21.CHECK STEERING WHEEL CENTER POINT

Hide 45130 22.INSTALL HORN BUTTON ASSEMBLY

Hide 23. TORQUE SENSOR ZERO POINT CALIBRATION