Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0225220 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1925/78  Short in Rear Pretensioner Squib LH Circuit  B1926/78  Open in Rear Pretensioner Squib LH Circuit  B1927/78  Short to GND in Rear Pretensioner Squib LH Circuit  B1928/78  Short to B+ in Rear Pretensioner Squib LH Circuit  


DESCRIPTION

The rear pretensioner squib LH circuit consists of the airbag ECU assembly and rear seat 3 point type outer belt assembly LH.

The airbag ECU assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1925/78 Short in Rear Pretensioner Squib LH Circuit
·

The airbag ECU assembly detects a line short in the rear pretensioner squib LH circuit during the primary check.

·

Rear pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag ECU assembly


Applies to check mode
B1926/78 Open in Rear Pretensioner Squib LH Circuit
·

The airbag ECU assembly detects an open in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag ECU assembly


Applies to check mode
B1927/78 Short to GND in Rear Pretensioner Squib LH Circuit
·

The airbag ECU assembly detects a short to ground in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag ECU assembly


Applies to check mode
B1928/78 Short to B+ in Rear Pretensioner Squib LH Circuit
·

The airbag ECU assembly detects a short to B+ in the rear pretensioner squib LH circuit.

·

Rear pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Floor wire

·

Rear pretensioner squib LH (Rear seat 3 point type outer belt assembly LH)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C316539E53
0.698,2.646 3.24,3.063 2.542,0.417 10 false Rear Pretensioner Squib LH (Rear Seat 3 Point Type Outer Belt Assembly LH) 0.698,2.49 1.25,2.958 0.552,0.469 10 false M41 4.698,3.167 6.344,3.49 1.646,0.323 10 false Airbag ECU Assembly 4.688,3.01 5.896,3.365 1.208,0.354 10 false M2*1, M1*2 4.688,1.167 5.198,1.458 0.51,0.292 10 false PLR+ 4.688,2.01 5.167,2.25 0.479,0.24 10 false PLR- 4.104,1.063 4.844,1.396 0.74,0.333 10 false 4*1, 8*2 4.104,1.896 4.917,2.167 0.813,0.271 10 false 5*1, 7*2 2.063,1.063 2.573,1.406 0.51,0.344 10 false RL+ 2.083,1.896 2.583,2.208 0.5,0.313 10 false RL- 2.406,1.063 2.781,1.281 0.375,0.219 10 false 1 2.406,1.896 2.781,2.115 0.375,0.219 10 false 2 0.167,3.24 2.969,3.542 2.802,0.302 10 false *1: w/o Passenger Airbag ON/OFF Indicator 0.167,3.5 2.969,3.802 2.802,0.302 10 false *2: w/ Passenger Airbag ON/OFF Indicator

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C284699C02
0.49,1.219 0.49,1.719 false 0.49,3.51 0.49,4.01 false 1.344,1.063 1.344,0.604 1.344,0.604 1.479,0.604 false 1.344,3.365 1.344,2.906 1.344,2.906 1.479,2.906 false 0.125,0.125 0.5,0.365 0.375,0.24 10 false *A 0.135,2.438 0.51,2.677 0.375,0.24 10 false *B 0.396,1.74 0.719,1.948 0.323,0.208 10 false *1 2.427,1.063 2.74,1.26 0.313,0.198 10 false *2 1.521,0.521 1.833,0.719 0.313,0.198 10 false *3 0.406,4.031 0.719,4.229 0.313,0.198 10 false *1 2.427,3.667 2.74,3.865 0.313,0.198 10 false *2 1.521,2.823 1.833,3.021 0.313,0.198 10 false *3 2,1.063 2.156,1.26 0.156,0.198 10 false A 1.594,1.063 1.75,1.26 0.156,0.198 10 false B 1.021,1.063 1.177,1.26 0.156,0.198 10 false C 0.615,1.063 0.771,1.26 0.156,0.198 10 false D 2,3.354 2.156,3.552 0.156,0.198 10 false A 1.594,3.354 1.75,3.552 0.156,0.198 10 false B 1.021,3.354 1.177,3.552 0.156,0.198 10 false C 0.615,3.354 0.771,3.552 0.156,0.198 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag ECU Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear seat 3 point type outer belt assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear seat 3 point type outer belt assembly LH and airbag ECU assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the rear seat 3 point type outer belt assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
a.

Connect the connector to the airbag ECU assembly.

C284700C04
0.885,1.719 1.229,1.938 0.344,0.219 4.49,1.729 4.844,1.958 0.354,0.229 2.042,1.823 2.198,1.823 false 5.667,1.823 5.823,1.823 false 1.104,0.729 1.104,0.969 false 4.729,0.49 4.729,0.729 false 0.531,0.135 0.906,0.375 0.375,0.24 10 false *A 3.979,0.156 4.354,0.396 0.375,0.24 10 false *B 4.635,0.75 4.948,0.948 0.313,0.198 10 false *1 6.021,0.594 6.333,0.792 0.313,0.198 10 false *2 1.01,0.99 1.323,1.188 0.313,0.198 10 false *1 2.375,0.583 2.688,0.781 0.313,0.198 10 false *2 0.823,1.323 1.135,1.521 0.313,0.198 10 false *a 4.448,1.313 4.76,1.51 0.313,0.198 10 false *a 2.24,1.74 2.698,1.938 0.458,0.198 10 false SST 5.865,1.74 6.323,1.938 0.458,0.198 10 false SST 0.938,1.75 1.25,1.948 0.313,0.198 10 false M41 5.667,0.344 5.823,0.542 0.156,0.198 10 false A 5.531,0.344 5.688,0.542 0.156,0.198 10 false B 5.125,0.344 5.281,0.542 0.156,0.198 10 false C 4.823,0.344 4.979,0.542 0.156,0.198 10 false D 2.042,0.583 2.198,0.781 0.156,0.198 10 false A 1.906,0.583 2.063,0.781 0.156,0.198 10 false B 1.5,0.583 1.656,0.781 0.156,0.198 10 false C 1.198,0.583 1.354,0.781 0.156,0.198 10 false D 4.542,1.76 4.958,2.073 0.417,0.313 10 false M41
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Rear Seat 3 Point Type Outer Belt Assembly LH *2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH)
- -



b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the rear seat 3 point type outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.


HINT:

Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.

Disconnect the floor wire from the airbag ECU assembly.

C284701C05
0.99,1.823 1.333,2.073 0.344,0.25 4.542,1.813 4.875,2.042 0.333,0.229 1.385,1.583 1.635,1.844 false 1.781,1.844 2.063,1.583 false 1,0.719 1,1.031 false 4.563,0.479 4.563,0.792 false 5.219,0.479 5.219,0.792 false 1.521,0.302 1.667,0.302 1.667,0.302 1.667,0.604 false 4.958,1.573 5.208,1.833 false 5.323,1.833 5.604,1.573 false 0.531,0.115 0.906,0.354 0.375,0.24 10 false *A 4.031,0.125 4.406,0.365 0.375,0.24 10 false *B 0.906,1.052 1.219,1.25 0.313,0.198 10 false *1 6.042,0.583 6.354,0.781 0.313,0.198 10 false *2 5.135,0.813 5.448,1.01 0.313,0.198 10 false *3 4.479,0.813 4.792,1.01 0.313,0.198 10 false *1 2.49,0.594 2.802,0.792 0.313,0.198 10 false *2 1.344,0.219 1.656,0.417 0.313,0.198 10 false *3 0.802,1.427 1.115,1.625 0.313,0.198 10 false *a 4.354,1.427 4.667,1.625 0.313,0.198 10 false *a 1.042,1.865 1.427,2.146 0.385,0.281 10 false M41 4.583,1.844 4.948,2.167 0.365,0.323 10 false M41 1.115,1.5 1.427,1.698 0.313,0.198 10 false RL+ 4.667,1.5 4.979,1.698 0.313,0.198 10 false RL+ 2.094,1.5 2.469,1.708 0.375,0.208 10 false RL- 5.646,1.5 6.01,1.708 0.365,0.208 10 false RL- 5.688,0.333 5.844,0.531 0.156,0.198 10 false A 5.375,0.333 5.531,0.531 0.156,0.198 10 false B 4.958,0.333 5.115,0.531 0.156,0.198 10 false C 4.656,0.333 4.813,0.531 0.156,0.198 10 false D 2.125,0.583 2.281,0.781 0.156,0.198 10 false A 1.823,0.583 1.979,0.781 0.156,0.198 10 false B 1.406,0.583 1.563,0.781 0.156,0.198 10 false C 1.104,0.583 1.26,0.781 0.156,0.198 10 false D
*A w/o Passenger Airbag ON/OFF Indicator *B w/ Passenger Airbag ON/OFF Indicator
*1 Rear Seat 3 Point Type Outer Belt Assembly LH *2 Airbag ECU Assembly
*3 Floor Wire - -
*a Front view of wire harness connector
(to Rear Seat 3 Point Type Outer Belt Assembly LH)
- -



b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M41-1 (RL+) - Body ground Power switch on (IG) Below 1 V
M41-2 (RL-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (RL+) - M41-2 (RL-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (RL+) - Body ground Always 1 MΩ or higher
M41-2 (RL-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (RL+) - M41-2 (RL-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C284702C02
0.781,1.26 0.781,1.667 false 0.781,3.302 0.781,3.708 false 0.125,0.135 0.5,0.375 0.375,0.24 10 false *A 0.115,2.281 0.49,2.521 0.375,0.24 10 false *B 0.688,1.688 1,1.885 0.313,0.198 10 false *1 0.688,3.74 1,3.938 0.313,0.198 10 false *1 2.135,1.115 2.448,1.313 0.313,0.198 10 false *2 2.146,3.458 2.458,3.656 0.313,0.198 10 false *2 1.729,1.115 1.885,1.313 0.156,0.198 10 false A 1.563,1.115 1.719,1.313 0.156,0.198 10 false B 1.063,1.115 1.219,1.313 0.156,0.198 10 false C 0.906,1.115 1.063,1.313 0.156,0.198 10 false D 1.729,3.146 1.885,3.344 0.156,0.198 10 false A 1.563,3.146 1.719,3.344 0.156,0.198 10 false B 1.063,3.146 1.219,3.344 0.156,0.198 10 false C 0.906,3.146 1.063,3.344 0.156,0.198 10 false D
*A w/o Passenger Airbag ON/OFF Indicator
*B w/ Passenger Airbag ON/OFF Indicator
*1 Rear Seat 3 Point Type Outer Belt Assembly LH
*2 Airbag ECU Assembly


Connect the connectors to the rear seat 3 point type outer belt assembly LH and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1925/78, B1926/78, B1927/78 or B1928/78 is not output.


HINT:

Codes other than DTCs B1925/78, B1926/78, B1927/78 and B1928/78 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG