Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR(for Center Pillar)
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230375 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89860A 1.INSTALL SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



d.

Connect the connector to the side airbag sensor assembly.

C198070C15
3.719,1.219 4.156,1.583 true 1.51,0.927 0.99,0.531 true 3.479,1.146 2.958,0.75 true 5.875,1.448 6.313,1.813 true 4.177,1.604 4.354,1.771 0.177,0.167 10 false *a 3.573,1.74 3.76,1.885 0.188,0.146 10 false *b 6.354,1.833 6.542,1.979 0.188,0.146 10 false *a 0.854,0.438 1.146,0.656 0.292,0.219 10 false A 2.813,0.635 3.104,0.854 0.292,0.219 10 false A
*a White Housing Lock *b Connect


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




e.

Engage the claw and install the side airbag sensor assembly with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side airbag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the side airbag sensor assembly claw is securely inserted into the body hole.




f.

Check that there is no looseness in the installed parts of the side airbag sensor assembly.


Hide 89860C 2.INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY (w/ Airbag Cut Off Switch)

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct



d.

Engage the claw and install the side No. 2 airbag sensor assembly with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side No. 2 airbag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the side No. 2 airbag sensor assembly claw is securely inserted into the body hole.




e.

Connect the connector to the side No. 2 airbag sensor assembly.

B312074C10
2.208,0.802 2.385,0.531 true 2.385,0.531 2.583,0.531 false 2.417,1.01 3,0.792 true 3.052,0.677 3.26,0.885 0.208,0.208 10 false *a 5.938,3.365 6.25,3.521 0.313,0.156 10 false *b 2.615,0.469 2.948,0.698 0.333,0.229 10 false A
*a White Housing Lock *b Connection is completed


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




f.

Check that there is no looseness in the installed parts of the side No. 2 airbag sensor assembly.


Hide 62414A 3.INSTALL LOWER CENTER PILLAR GARNISH

Hide 62332A 4.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67917A 5.INSTALL REAR DOOR SCUFF PLATE

Hide 62312B 6.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67914 7.INSTALL FRONT DOOR SCUFF PLATE

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION