Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR
RM3210E _58 Vehicle Interior _047539 SUPPLEMENTAL RESTRAINT SYSTEMS _0230376 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


PROCEDURE

Hide 89834 1.INSTALL REAR AIRBAG SENSOR

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



d.

Engage the claw and install the rear airbag sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the rear airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the rear airbag sensor claw is securely inserted into the body hole.




e.

Connect the connector to the rear airbag sensor.

C198070C15
3.719,1.219 4.156,1.583 true 1.51,0.927 0.99,0.531 true 3.479,1.146 2.958,0.75 true 5.875,1.448 6.313,1.813 true 4.177,1.604 4.354,1.771 0.177,0.167 10 false *a 3.573,1.74 3.76,1.885 0.188,0.146 10 false *b 6.354,1.833 6.542,1.979 0.188,0.146 10 false *a 0.854,0.438 1.146,0.656 0.292,0.219 10 false A 2.813,0.635 3.104,0.854 0.292,0.219 10 false A
*a White Housing Lock *b Connect


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




f.

Check that there is no looseness in the installed parts of the rear airbag sensor.


Hide 62552F 2.INSTALL REAR SEAT SIDE GARNISH

Hide 71304C 3.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 62332A 4.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 76974F 5.INSTALL REAR UNDER SIDE COVER LH (for LH Side)

Hide 76973F 6.INSTALL REAR UNDER SIDE COVER RH (for RH Side)

Hide 67918A 7.INSTALL REAR DOOR SCUFF PLATE

Hide 8.INSTALL REAR SEATBACK ASSEMBLY

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION