Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0232459 PARKING ASSIST MONITOR SYSTEM C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly*1 or radio and display receiver assembly*2 judges that the signals or signal lines between the rear television camera assembly and the navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2



*1: for Navigation Receiver Type

*2: for Radio and Display Receiver Type


WIRING DIAGRAM

E345335E01
2.917,2.698 4.938,2.896 2.021,0.198 10 false *1: for Navigation Receiver Type 0.094,2.979 2.708,3.229 2.615,0.25 10 false Radio and Display Receiver Assembly*2 2.896,3.063 5.542,3.281 2.646,0.219 10 false *2: for Radio and Display Receiver Type 2.906,3.375 5.552,3.594 2.646,0.219 10 false *3: Shielded 3.813,1.656 4.104,1.833 0.292,0.177 10 false *3 5.438,2.5 7.042,2.917 1.604,0.417 10 false Rear Television Camera Assembly 0.094,2.656 2.115,2.854 2.021,0.198 10 false Navigation Receiver Assembly*1 5.417,2.323 5.708,2.5 0.292,0.177 10 false R5 1.292,0.635 1.688,0.885 0.396,0.25 10 false CA+ 1.375,1.021 1.771,1.271 0.396,0.25 10 false V+ 1.396,1.427 1.792,1.677 0.396,0.25 10 false V- 1.208,1.813 1.729,2.042 0.521,0.229 10 false CGND 2.146,2.208 2.542,2.458 0.396,0.25 10 false F32 1.208,2.229 1.656,2.479 0.448,0.25 10 false GND1 1.76,2.229 2.073,2.479 0.313,0.25 10 false F93 5.417,1.813 5.865,2.063 0.448,0.25 10 false CGND 5.438,1.417 5.833,1.667 0.396,0.25 10 false CV- 5.448,1.01 5.844,1.26 0.396,0.25 10 false CV+ 5.427,0.615 5.823,0.865 0.396,0.25 10 false CB+ 2.135,0.615 2.531,0.865 0.396,0.25 10 false F34 1.74,0.635 2.135,0.885 0.396,0.25 10 false F95 2.135,0.438 2.531,0.688 0.396,0.25 10 false 11*2 1.729,0.438 2.125,0.688 0.396,0.25 10 false 11*1 2.146,0.844 2.542,1.094 0.396,0.25 10 false 12*2 1.74,1.042 2.135,1.292 0.396,0.25 10 false F95 1.74,1.438 2.135,1.688 0.396,0.25 10 false F95 1.74,1.844 2.135,2.094 0.396,0.25 10 false F95 2.146,1.042 2.542,1.292 0.396,0.25 10 false F34 2.146,1.427 2.542,1.677 0.396,0.25 10 false F34 2.146,1.813 2.542,2.063 0.396,0.25 10 false F34 2.156,1.229 2.552,1.479 0.396,0.25 10 false 24*2 2.167,1.615 2.563,1.865 0.396,0.25 10 false 23*2 2.156,2.021 2.552,2.271 0.396,0.25 10 false 7*2 1.74,0.844 2.135,1.094 0.396,0.25 10 false 12*1 1.75,1.24 2.146,1.49 0.396,0.25 10 false 24*1 1.75,1.635 2.146,1.885 0.396,0.25 10 false 23*1 1.781,2.031 2.177,2.281 0.396,0.25 10 false 7*1 5.208,0.531 5.604,0.781 0.396,0.25 10 false 6 5.229,1.323 5.625,1.573 0.396,0.25 10 false 2 5.219,0.927 5.615,1.177 0.396,0.25 10 false 3 5.24,1.729 5.635,1.979 0.396,0.25 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Navigation Receiver Type A
for Radio and Display Receiver Type B



A

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F95 navigation receiver assembly connector.


b.

Disconnect the R5 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-11 (CA+) - R5-6 (CB+) Always Below 1 Ω
F95-12 (V+) - R5-3 (CV+) Always Below 1 Ω
F95-24 (V-) - R5-2 (CV-) Always Below 1 Ω
F95-23 (CGND) - R5-5 (CGND) Always Below 1 Ω
F95-11 (CA+) or R5-6 (CB+) - Body ground Always 10 kΩ or higher
F95-12 (V+) or R5-3 (CV+) - Body ground Always 10 kΩ or higher
F95-24 (V-) or R5-2 (CV-) - Body ground Always 10 kΩ or higher
F95-23 (CGND) or R5-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)
a.

Reconnect the F95 navigation receiver assembly connector.


b.
E289208C16
1.479,0.115 1.958,0.438 0.479,0.323 0.781,0.667 1.24,1.115 false 1.219,1.844 1.229,1.323 false 0.458,0.49 0.865,0.802 0.406,0.313 10 false CA+ 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.188 2.01,0.406 0.396,0.219 10 false F95 0.99,1.917 1.49,2.146 0.5,0.229 10 false CGND
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F95-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F95-11 (CA+) - F95-23 (CGND) Power switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)

NG

4.INSPECT NAVIGATION RECEIVER ASSEMBLY (V+, GND1)
a.

Reconnect the R5 rear television camera assembly connector.


b.
E289209C07
1.479,0.188 1.927,0.469 0.448,0.281 1.531,2.438 1.938,2.708 0.406,0.271 2.406,4.271 1.854,3.719 false 1.115,1.198 0.625,0.896 false 0.167,0.125 0.479,0.354 0.313,0.229 10 false *a 1.594,0.24 1.979,0.458 0.385,0.219 10 false F95 0.406,0.771 0.708,0.99 0.302,0.219 10 false V+ 2.479,4.302 2.979,4.573 0.5,0.271 10 false GND1 1.625,2.49 2.01,2.708 0.385,0.219 10 false F93
*a Component with harness connected
(Navigation Receiver Assembly)


E265840C05
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.

Item Content
Measurement terminal F95-12 (V+) - F93-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F34 radio and display receiver assembly connector.


b.

Disconnect the R5 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-11 (CA+) - R5-6 (CB+) Always Below 1 Ω
F34-12 (V+) - R5-3 (CV+) Always Below 1 Ω
F34-24 (V-) - R5-2 (CV-) Always Below 1 Ω
F34-23 (CGND) - R5-5 (CGND) Always Below 1 Ω
F34-11 (CA+) or R5-6 (CB+) - Body ground Always 10 kΩ or higher
F34-12 (V+) or R5-3 (CV+) - Body ground Always 10 kΩ or higher
F34-24 (V-) or R5-2 (CV-) - Body ground Always 10 kΩ or higher
F34-23 (CGND) or R5-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+, CGND)
a.

Reconnect the F34 radio and display receiver assembly connector.


b.
E289208C15
1.479,0.115 1.958,0.438 0.479,0.323 0.781,0.667 1.24,1.115 false 1.219,1.844 1.229,1.323 false 0.458,0.49 0.865,0.802 0.406,0.313 10 false CA+ 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.188 2.01,0.406 0.396,0.219 10 false F34 0.99,1.917 1.49,2.146 0.5,0.229 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F34-11 (CA+) - F34-23 (CGND) Power switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (V+, GND1)
a.

Reconnect the R5 rear television camera assembly connector.


b.
E289209C06
1.479,0.188 1.927,0.469 0.448,0.281 1.531,2.438 1.938,2.708 0.406,0.271 2.406,4.271 1.854,3.719 false 1.115,1.198 0.625,0.896 false 0.167,0.125 0.479,0.354 0.313,0.229 10 false *a 1.594,0.24 1.979,0.458 0.385,0.219 10 false F34 0.406,0.771 0.708,0.99 0.302,0.219 10 false V+ 2.479,4.302 2.979,4.573 0.5,0.271 10 false GND1 1.625,2.49 2.01,2.708 0.385,0.219 10 false F32
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C05
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.

Item Content
Measurement terminal F34-12 (V+) - F32-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the power switch is on (ACC).




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY