Use the following procedure to troubleshoot the parking assist monitor system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
| Problem Symptom | Cause |
|---|---|
|
*: DTCs output as "Hist" will not be output again after DTCs are cleared. |
|
Both of the following conditions are met:
·
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. ·
DTC C1622 is output as "Hist" only.* |
The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the power switch off.
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Navigation System.
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>PROBLEM SYMPTOMS TABLE
for Radio and Display Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Navigation system is normal | A |
| Navigation system is abnormal | B |
A
B
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>HOW TO PROCEED WITH TROUBLESHOOTING
for Radio and Display Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>HOW TO PROCEED WITH TROUBLESHOOTING
Use the GTS to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and make a note of any codes that are output.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs. Try to reproduce the DTCs by duplicating the detection conditions of the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTCs are output | B |
A
B
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Diagnosis System
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>DIAGNOSIS SYSTEM
Terminals of ECU
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Data List / Active Test
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT