Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat)
RM3210E _58 Vehicle Interior _047549 SEAT _0234655 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Power seat is available only on the driver side.

·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY LH

a.
B439710

Place the front seat assembly LH in the cabin.

NOTICE:

Be careful not to damage the vehicle body.



b.

Connect the front seat airbag assembly LH connector under the front seat assembly LH.

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C01
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.


·

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.





c.

Connect each connector and engage each clamp under the front seat assembly LH.


d.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


e.

Temporarily install the front seat assembly LH with the 4 bolts.


f.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


g.
B439709N01
0.083,0.813 0.24,1.01 0.156,0.198 10 true 1 1.708,1.865 1.865,2.063 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly LH.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



h.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the foremost position.


i.
B439708N01
2.177,1.656 2.333,1.854 0.156,0.198 10 true 1 1.083,1.646 1.24,1.844 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly LH.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



Hide 72158 2.INSTALL INNER SEAT TRACK BRACKET COVER LH

a.
B439785

Engage the 2 claws and guide to install the inner seat track bracket cover LH.


Hide 72138 3.INSTALL OUTER SEAT TRACK COVER LH

a.
B439784

Engage the 2 claws and guide to install the outer seat track cover LH.


Hide 72128A 4.INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH

a.

Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.


b.
B439783

Engage the 2 claws to install the front inner seat track bracket cover LH.


Hide 72124 5.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH

a.
B439782

Engage the 2 claws to install the front outer seat track bracket cover LH.


Hide 71910A 6.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly LH.