Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0234839 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during occupant detection sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT CLEARANCE SONAR SYSTEM>CALIBRATION

CAUTION:
·
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL


Hide 73230 2.REMOVE FRONT SEAT INNER BELT ASSEMBLY

Hide 71074S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 72551 4.REMOVE NO. 1 RECLINING HINGE COVER

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 72526A 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 71811D 6.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71861 7.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 8.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 9.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

HINT:

Use the same procedure as for the driver seat.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>DISASSEMBLY


Hide 71512S 10.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

a.

Using a screwdriver, disengage the 13 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B442318C01
1.542,2.469 1.927,2.385 true 1.979,2.292 2.219,2.552 0.24,0.26 10 false *a
*a Screwdriver - -