Home › Engine / Hybrid System › 2ZR-FXE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM3210E _51 Engine / Hybrid System _047498 2ZR-FXE INTAKE / EXHAUST _0236618 EXHAUST MANIFOLD A

2ZR-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Install a new exhaust manifold to head gasket and a new EGR cooler gasket to the cylinder head sub-assembly.


b.

Temporarily install the exhaust manifold (TWC: Front Catalyst) to the cylinder head sub-assembly with 7 new nuts.


c.

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and cylinder block sub-assembly with the 3 bolts.


d.
A376899N01
1.344,0.031 1.469,0.208 0.125,0.177 10 true 2 2,0.135 2.156,0.333 0.156,0.198 10 true 1 2.625,0.021 2.781,0.219 0.156,0.198 10 true 3 0.938,0.292 1.094,0.49 0.156,0.198 10 true 4 3.01,0.271 3.167,0.469 0.156,0.198 10 true 5 0.396,0.052 0.542,0.24 0.146,0.188 10 false 7 0.229,0.583 0.375,0.771 0.146,0.188 10 true 6

Using a 12 mm deep socket wrench, tighten the 7 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
A376898N01
0.354,1.156 0.51,1.354 0.156,0.198 10 true 1 2.698,0.469 2.854,0.667 0.156,0.198 10 true 2 2.802,1.469 2.958,1.667 0.156,0.198 10 true 3

Tighten the 3 bolts in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

for LHD:

i.

Engage the clamp.


ii.
A378762C01
0,0 0,0 false
V113147

Connect
V113148

Lock


Connect the brake booster pump assembly connector and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.





g.

w/ Exhaust Heat Recirculation System:

i.

Connect the engine coolant temperature sensor connector.


ii.

Connect the water pipe and hose sub-assembly A to the bracket with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 17167 3.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 6 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 82715 4.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket to the cylinder head sub-assembly with the bolt and engage the clamp.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gaskets.

·

Do not damage the exhaust pipe gaskets.

·

Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 2 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C37
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Engage the wire harness clamp.


h.

Connect the heated oxygen sensor connector.


i.

w/ Exhaust Heat Recirculation System:

i.

Connect the outlet heater water hose B and outlet heater water hose C to the No. 2 outlet water pipe and inlet water pipe and slide the 2 clips to secure them.

NOTICE:

When installing the outlet heater water hose B and outlet heater water hose C, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.




Hide 7.ADD ENGINE COOLANT (w/ Exhaust Heat Recirculation System)

Hide 8.INSPECT FOR COOLANT LEAK (w/ Exhaust Heat Recirculation System)

Hide 57533B 10.INSTALL FRONT CENTER FLOOR BRACE

a.

Install the 3 front center floor braces to the vehicle body with the 12 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 58166 11.INSTALL FRONT FLOOR COVER LH

a.

Engage the 5 clamps to install the front floor cover LH to the vehicle body with the 2 bolts and 3 clips.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 58165B 12.INSTALL FRONT FLOOR COVER RH

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 51442 13.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 14.INSTALL NO. 1 ENGINE UNDER COVER

Hide 51444C 15.INSTALL REAR MOTOR UNDER COVER LH (w/ Exhaust Heat Recirculation System)