The combination meter assembly (meter circuit plate) receives text data signals from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.
Based on these signals, audio and visual system or navigation system information is displayed on the multi-information display.
This DTC is stored when the combination meter assembly (meter circuit plate) cannot receive the signal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150A | Lost Communication with HMI-LAN | After the combination meter assembly (meter circuit plate) receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the power switch is on (ACC), 1 or more times, the combination meter assembly (meter circuit plate) cannot receive the signal for 30 seconds or more. | ·
Harness or connector ·
Navigation receiver assembly*1 ·
Radio and display receiver assembly*2 ·
Combination meter assembly (Meter circuit plate) |
DTC stored | - |
*1: for Navigation Receiver Type
*2: for Radio and Display Type
w/ Navigation System
w/o Navigation System
DTC B150A may be stored if the auxiliary battery voltage dropped.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Navigation System | A |
| w/o Navigation System | B |
A
B
Check if navigation system DTCs are output.
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Navigation system DTCs are not output. | A |
| Navigation system DTCs are output. | B |
A
B
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Disconnect the F6 combination meter assembly (meter circuit plate) connector.
Disconnect the F34 radio and display receiver assembly*1 or F95 navigation receiver assembly*2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-33 (MSCH) - F34-3 (CNH1)*1 | Always | Below 1 Ω |
| F6-34 (MSCL) - F34-4 (CNL1)*1 | Always | Below 1 Ω |
| F6-33 (MSCH) or F34-3 (CNH1) - Body ground*1 | Always | 10 kΩ or higher |
| F6-34 (MSCL) or F34-4 (CNL1) - Body ground*1 | Always | 10 kΩ or higher |
| F6-33 (MSCH) - F95-3 (CNH1)*2 | Always | Below 1 Ω |
| F6-34 (MSCL) - F95-4 (CNL1)*2 | Always | Below 1 Ω |
| F6-33 (MSCH) or F95-3 (CNH1) - Body ground*2 | Always | 10 kΩ or higher |
| F6-34 (MSCL) or F95-4 (CNL1) - Body ground*2 | Always | 10 kΩ or higher |
*1: for Radio and Display Type
*2: for Navigation Receiver Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly (meter circuit plate) with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY
Turn the power switch on (IG) and wait 30 seconds.
A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly (meter circuit plate) and navigation receiver assembly.
Operate the steering pad switch assembly and check that the audio tab illuminates.
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| The audio tab illuminates and DTC B150A is not output. | A |
| The audio tab does not illuminate and DTC B150A is output (for Radio and Display Type). | B |
| The audio tab does not illuminate and DTC B150A is output (for Navigation Receiver Type). | C |
A
B
C
Check if audio and visual system DTCs are output.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Audio and visual system DTCs are not output. | A |
| Audio and visual system DTCs are output. | B |
A
B
Disconnect the F6 combination meter assembly (meter circuit plate) connector.
Disconnect the F34 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-33 (MSCH) - F34-3 (CNH1) | Always | Below 1 Ω |
| F6-34 (MSCL) - F34-4 (CNL1) | Always | Below 1 Ω |
| F6-33 (MSCH) or F34-3 (CNH1) - Body ground | Always | 10 kΩ or higher |
| F6-34 (MSCL) or F34-4 (CNL1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly (meter circuit plate) with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY
Turn the power switch on (IG) and wait 30 seconds.
A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly (meter circuit plate) and radio and display receiver assembly.
Operate the steering pad switch assembly and check that the audio tab illuminates.
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| The audio tab illuminates and DTC B150A is not output. | A |
| The audio tab does not illuminate and DTC B150A is output. | B |
A
B