Home › Brake › BRAKE (FRONT) › FRONT DISC BRAKE PAD
RM3210E _54 Brake _047520 BRAKE (FRONT) _0237142 FRONT DISC BRAKE PAD A

BRAKE (FRONT)  FRONT DISC BRAKE PAD  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front disc brake pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISABLE BRAKE CONTROL

Hide 3.REMOVE FRONT WHEEL

Hide 4.REMOVE FRONT DISC BRAKE PAD

CAUTION:

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when removing the front disc brake pads.


a.
C344544C02
1.552,2.875 1.865,3.031 0.313,0.156 10 false *a 0.813,2.823 1.125,2.979 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the front disc brake cylinder slide pin (lower side) and remove the bolt.


b.

Pull the front disc brake cylinder assembly upward.


c.
C344545C01
0,0 0,0 false

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 04945 5.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 04945 6.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 7.INSTALL FRONT DISC BRAKE PAD

CAUTION:

Be careful not to get pinched by the front disc brake cylinder assembly or other parts when installing the front disc brake pads.


a.

Push in the front disc brake piston.

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the front disc brake piston.




b.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.

·

Install the front disc brake pad so that the pad wear indicator plate is mounted on the upper side of the vehicle.




c.

Hold the front disc brake cylinder slide pin (lower side) and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


c.

Turn the power switch on (READY).


d.

Depress the brake pedal and release it.



Hide 9.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 10.INSTALL FRONT WHEEL