This DTC is applicable to models w/ Flow Shutting Valve only.
Refer to DTC P268111.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P268111
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P26819C | Engine Coolant Bypass Valve Low / Insufficient Flow | The actual increase in engine coolant temperature is less than calculated based on the intake air volume (2 trip detection logic). | ·
Engine coolant level low ·
Air in cooling system (for Engine) ·
Engine coolant leak ·
Flow shutting valve (water valve) ·
Engine coolant temperature sensor ·
Engine water pump assembly |
Does not come on | DTC stored | SAE Code: P26A3 |
If the actual increase in engine coolant temperature is less than calculated based on the total intake air volume since the engine started, the ECM will judge that the flow shutting valve (water valve) is clogged and store this DTC.
Make sure to perform this procedure when the ambient temperature is 5°C (41°F) or more, the engine coolant temperature between 5 and 40°C (41 and 104°F), and the difference between the engine coolant temperature and ambient temperature is within 10°C (18°F).
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Enter the following menus: Powertrain / Engine / Data List / Coolant Water Route Switching Valve.
Start the engine with A/C switch and all other accessories off, release the accelerator pedal and check that the value of Data List item Engine Coolant Valve is "Closed".
Idle the engine for 2 minutes or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P26819C.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.
Click hereEngine / Hybrid System>2ZR-FXE COOLING>COOLANT(for Engine)>REPLACEMENT
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P26819C is output | A |
| DTC P26819C and other DTCs are output | B |
If DTC P268172 and P26819C are output simultaneously, perform troubleshooting for DTC P26819C first.
If DTC P268173 and P26819C are output simultaneously, perform troubleshooting for DTC P268173 first.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>P268172
If any DTCs other than DTC P268172, P268173 or P26819C are output, perform troubleshooting for those DTCs first.
A
B
Check that the engine coolant level is between the FULL and LOW lines.
The engine coolant is not excessively low.
Make sure that there are no signs of the engine overheating.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair any engine coolant leaks.
Add engine coolant and perform air bleeding after repair.
Click hereEngine / Hybrid System>2ZR-FXE COOLING>COOLANT(for Engine)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P26819C is output | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the Electric Water Pump.
| Tester Display |
|---|
| Activate the Electric Water Pump |
Perform the Active Test according to the display on the GTS and lightly squeeze a radiator hose by hand to check for a pulsing feeling.
Pulsing can be felt in a radiator hose.
If pulsing cannot be felt in a radiator hose, inspect the engine water pump assembly. If the impeller is damaged, replace the engine water pump assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature and Heater Coolant Temperature Sensor.
| Tester Display |
|---|
| Coolant Temperature |
| Heater Coolant Temperature Sensor |
Start the engine.
Read the value displayed on the GTS.
The values of Data List items Coolant Temperature and Heater Coolant Temperature Sensor change as the engine warms up and do not get stuck on a certain value.
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2ZR-FXE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>INITIALIZATION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Value of Data List item Coolant Temperature does not change) | B |
| NG (Value of Data List item Heater Coolant Temperature does not change) | C |
A
B
C
Replace the flow shutting valve (water valve).
Click hereEngine / Hybrid System>2ZR-FXE COOLING>FLOW SHUTTING VALVE>REMOVAL
When replacing any cooling system (for Engine) parts, if excessive deposits of rust or scale exist or the concentration of the engine coolant is abnormal, replace the engine coolant.
Click hereEngine / Hybrid System>2ZR-FXE COOLING>COOLANT(for Engine)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the power switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Engine Water Pump Assembly |
| *2 | Impeller |
Visually inspect the impeller for damage.
The impeller is not damaged.
If the impeller is damaged, replace the engine water pump assembly.
Click hereEngine / Hybrid System>2ZR-FXE COOLING>WATER PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT