Home › Engine / Hybrid System › 2ZR-FXE ENGINE CONTROL › ENGINE COOLANT TEMPERATURE SENSOR
RM3210E _51 Engine / Hybrid System _047494 2ZR-FXE ENGINE CONTROL _0239233 ENGINE COOLANT TEMPERATURE SENSOR A

2ZR-FXE ENGINE CONTROL  ENGINE COOLANT TEMPERATURE SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine coolant temperature sensor or No. 2 engine coolant temperature sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Replacement of engine coolant temperature sensor Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)w/ Canister Pump Module
(Click here)w/o Canister Pump Module
for SFI system (w/ Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
for SFI system (w/o Canister Pump Module)

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration (Click here)

CAUTION:
A389825

Do not remove the reserve tank cap, air release valve (w/ air release valve) or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 51444C 1.REMOVE REAR MOTOR UNDER COVER LH

Hide 2.DRAIN ENGINE COOLANT (for Engine)

Hide 12601B 3.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 89422 5.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

a.
A375046

Disconnect the engine coolant temperature sensor connector.


b.
A375049C01
1.635,0.625 1.875,0.625 1.875,0.625 2.01,1.104 true 2.969,2.5 3.125,2.5 false 2.802,2.448 3,2.615 0.198,0.167 10 true *1 1.333,0.552 1.635,0.719 0.302,0.167 10 true SST
*1 Gasket


Using SST, remove the engine coolant temperature sensor from the water outlet.

SST
09817-33191  

NOTICE:

If the engine coolant temperature sensor has been struck or dropped, replace it.



c.

Remove the gasket from the engine coolant temperature sensor.


Hide G9200 6.REMOVE INVERTER WITH CONVERTER ASSEMBLY (w/ Flow Shutting Valve (Water Valve))

Hide 89422D 7.REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR (w/ Flow Shutting Valve (Water Valve))

a.
A375044

Disconnect the No. 2 engine coolant temperature sensor connector.


b.
A375045

Remove the clip and No. 2 engine coolant temperature sensor from the No. 2 water by-pass pipe.

NOTICE:

If the No. 2 engine coolant temperature sensor has been struck or dropped, replace it.