Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM
RM3210E _59 Vehicle Exterior _047541 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0237698 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  Sound does not Turn OFF when the Vehicle Approaching Speaker Switch is Pressed  


DESCRIPTION

When the pattern select switch assembly (vehicle approaching speaker switch) is pushed when the vehicle approaching speaker system is on, the hybrid vehicle control ECU receives a signal to temporarily suspend output of the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM

E343546E02
0.885,2.917 1.344,3.115 0.458,0.198 10 false F44 1.219,2.927 3.75,3.271 2.531,0.344 10 false Pattern Select Switch Assembly (Vehicle Approaching Speaker Switch) 4.563,3.167 6.385,3.563 1.823,0.396 10 false Hybrid Vehicle Control ECU 4.333,3.167 4.792,3.365 0.458,0.198 10 false F3 4.354,2.281 4.813,2.479 0.458,0.198 10 false 22 4.646,2.281 5.104,2.479 0.458,0.198 10 false SW 3.5,2.281 3.958,2.479 0.458,0.198 10 false 14 3.115,2.292 3.573,2.49 0.458,0.198 10 false ECU 3.219,1.885 3.469,2.042 0.25,0.156 10 false IG 3.5,1.885 3.958,2.083 0.458,0.198 10 false 6 0.875,1.354 1.333,1.552 0.458,0.198 10 false 3D 1.177,1.365 4.031,1.542 2.854,0.177 10 false Instrument Panel Junction Block Assembly 3.479,0.656 3.938,0.854 0.458,0.198 10 false 30 2.417,0.927 3.427,1.177 1.01,0.25 10 false ECU-IG1 NO. 4 1.333,0.708 2.323,1.052 0.99,0.344 10 false from IG1-NO. 1 Relay 5.625,1.948 6.083,2.146 0.458,0.198 10 false 5V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (Operation Cancel SW)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


f.

Read the Data List according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Operation Cancel SW Pattern select switch assembly (vehicle approaching speaker switch) signal OFF or ON OFF: Pattern select switch assembly (vehicle approaching speaker switch) is not pressed.
ON: Pattern select switch assembly (vehicle approaching speaker switch) is pressed.
-
Body Electrical > Vehicle Proximity Notification System > Data List
Tester Display
Operation Cancel SW
50003 393 5

Result:
Result Proceed to
The GTS display changes according to the operation of the vehicle approaching speaker switch A
The GTS display does not change according to the operation of the vehicle approaching speaker switch B



A

B

2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH)
2.INSPECT PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH)
a.

Remove the pattern select switch assembly (vehicle approaching speaker switch).

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER SWITCH>REMOVAL


b.

Inspect the pattern select switch assembly (vehicle approaching speaker switch).

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH) - IG POWER SOURCE)

NG

REPLACE PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH)

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH) - IG POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F44-6 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH))

NG

5.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH))
a.

Disconnect the F3 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-22 (SW) - F44-14 (ECU) Always Below 1 Ω
F3-22 (SW) or F44-14 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PATTERN SELECT SWITCH ASSEMBLY (VEHICLE APPROACHING SPEAKER SWITCH) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3D instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F44-6 (IG) - 3D-30 Always Below 1 Ω
F44-6 (IG) or 3D-30 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR