Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM3210E _58 Vehicle Interior _047538 SEAT BELT _0234841 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B434987E01
1.396,1.938 1.573,2.135 0.177,0.198 10 true A 0.823,0.719 1.042,0.917 0.219,0.198 10 false B

Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Fully tighten the bolt (A), and then the bolt (B) to install the front shoulder belt anchor adjuster assembly.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSPECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 73220 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B434986E01
0.958,0.25 1.146,0.469 0.188,0.219 10 true A 1.021,1.917 1.208,2.135 0.188,0.219 10 true B

Engage the 2 guides and temporarily install the front seat outer belt assembly with the 2 bolts.


b.

Fully tighten the bolt (A), and then the bolt (B) to install the front seat outer belt assembly.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B434988C01
2.135,0.813 2.417,0.625 true 1.969,0.771 2.271,1.01 0.302,0.24 10 false *a 2.219,0.208 2.521,0.469 0.302,0.26 10 false *b
*a Locking Button
*b Lock


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



d.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Check that the ELR locks.

NOTICE:

This check should be performed with the front seat outer belt assembly installed to the vehicle.


i.

With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.



Hide 62420A 4.INSTALL CENTER PILLAR GARNISH ASSEMBLY

Hide 62414A 5.INSTALL LOWER CENTER PILLAR GARNISH

Hide 73220 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73233 7.INSTALL LAP BELT OUTER ANCHOR COVER

a.

Engage the 3 claws to install the lap belt outer anchor cover.


Hide 62332A 8.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 9.INSTALL REAR DOOR SCUFF PLATE

Hide 62312B 10.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67914 11.INSTALL FRONT DOOR SCUFF PLATE

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION