This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly) detects that the sliding roof switch (map light assembly) is stuck for 30 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2342 | Switch Failure | Sliding roof ECU (sliding roof drive gear sub-assembly) detects sliding roof switch (map light assembly) is stuck for 30 seconds or more | ·
Sliding roof ECU (Sliding roof drive gear sub-assembly) ·
Sliding roof switch (Map light assembly) ·
Wire harness or connector |
Refer to DTC B2341.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>B2341
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
The sliding roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Sliding Roof / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Open Switch Failure(Past) | Open switch failure signal (Past) | OFF or ON | OFF: No sliding roof open switch failure signal (Past)
ON: Sliding roof open switch failure signal (Past) |
- |
| Close Switch Failure(Past) | Close switch failure signal (Past) | OFF or ON | OFF: No sliding roof close switch failure signal (Past)
ON: Sliding roof close switch failure signal (Past) |
- |
| Up Switch Failure(Past) | Up switch failure signal (Past) | OFF or ON | OFF: No sliding roof tilt up switch failure signal (Past)
ON: Sliding roof tilt up switch failure signal (Past) |
- |
| Down Switch Failure(Past) | Down switch failure signal (Past) | OFF or ON | OFF: No sliding roof tilt down switch failure signal (Past)
ON: Sliding roof tilt down switch failure signal (Past) |
- |
| Open Switch Failure(Current) | Open switch failure signal (Current) | OFF or ON | OFF: No sliding roof open switch failure signal (Current)
ON: Sliding roof open switch failure signal (Current) |
- |
| Close Switch Failure(Current) | Close switch failure signal (Current) | OFF or ON | OFF: No sliding roof close switch failure signal (Current)
ON: Sliding roof close switch failure signal (Current) |
- |
| Up Switch Failure(Current) | Up switch failure signal (Current) | OFF or ON | OFF: No sliding roof tilt up switch failure signal (Current)
ON: Sliding roof tilt up switch failure signal (Current) |
- |
| Down Switch Failure(Current) | Down switch failure signal (Current) | OFF or ON | OFF: No sliding roof tilt down switch failure signal (Current)
ON: Sliding roof tilt down switch failure signal (Current) |
- |
| Tester Display |
|---|
| Open Switch Failure(Past) |
| Close Switch Failure(Past) |
| Up Switch Failure(Past) |
| Down Switch Failure(Past) |
| Open Switch Failure(Current) |
| Close Switch Failure(Current) |
| Up Switch Failure(Current) |
| Down Switch Failure(Current) |
OFF is displayed for each Data List item.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Disconnect the O4 sliding roof switch (map light assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O10-10 (OPN) - Body ground | Always | 10 kΩ or higher |
| O10-8 (CLS) - Body ground | Always | 10 kΩ or higher |
| O10-5 (UP) - Body ground | Always | 10 kΩ or higher |
| O10-9 (DWN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL
Inspect the sliding roof switch (map light assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG