Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER
RM3210E _59 Vehicle Exterior _047542 EXTERIOR PANELS / TRIM _0243309 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  DISASSEMBLY  


PROCEDURE

Hide 89341M 1.REMOVE FRONT SIDE ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348J 2.REMOVE ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 89341K 3.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89341L 4.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89347D 5.REMOVE FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89347B 6.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 82113 7.REMOVE NO. 3 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

a.

w/o Fog Light:

i.

Disengage the 10 clamps and remove the No. 3 engine room wire.

B435201



b.

w/ Fog Light:

i.

Disengage the 10 clamps and remove the No. 3 engine room wire.

B435202



Hide 88211B 8.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)

Hide 52113D 9.REMOVE FRONT BUMPER EXTENSION LH (w/o Fog Light)

a.
B435204

Remove the 2 screws.


b.
B435205

Disengage the claw to remove the front bumper extension LH.


Hide 52112D 10.REMOVE FRONT BUMPER EXTENSION RH (w/o Fog Light)

HINT:

Use the same procedure for the LH side.


Hide 81220 11.REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 12.REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure for the LH side.


Hide 53879R 13.REMOVE FRONT FENDER LINER RETAINER

a.
B435203

Disengage the 2 claws to remove the 2 front fender liner retainers.

HINT:

Use the same procedure for the RH side and LH side.



Hide 53395E 14.REMOVE HOOD TO FRONT END PANEL SEAL

a.

Separate the double-sided tape and disengage the 2 clips to remove the hood to front end panel seal.

B435206C01
0,0 0,0 false
V100155

Double-sided Tape - -



Hide 53101 15.REMOVE RADIATOR GRILLE SUB-ASSEMBLY

a.

Remove the 2 screws and 4 clips.

B435207


b.
B435208C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 15 claws as shown in the illustration to remove the radiator grille sub-assembly.


Hide 17753 16.REMOVE NO. 3 AIR CLEANER INLET

a.
B435210

Remove the 2 screws.


b.
B435211

Disengage the 3 claws to remove the No. 3 air cleaner inlet.


Hide 53112E 17.REMOVE LOWER NO. 1 RADIATOR GRILLE

a.
B435212C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 18 claws as shown in the illustration to remove the lower No. 1 radiator grille.


Hide 52128B 18.REMOVE FRONT BUMPER HOLE COVER LH

a.
B435214C01
1.063,0.698 2.177,0.573 true 2.219,0.427 2.583,0.635 0.365,0.208 10 false *a
*a Hook
V113147

Remove in this Direction


Disengage the 2 claws as shown in the illustration.


b.

Disengage the hook to remove the front bumper hole cover LH.


Hide 52127D 19.REMOVE FRONT BUMPER HOLE COVER RH

HINT:

Use the same procedure for the LH side.


Hide 52114A 20.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET

a.

for Extension Mounting Bracket Type A:

i.
B435216

Remove the 2 screws.


ii.
B435217C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front bumper extension mounting bracket as shown in the illustration.



b.

for Extension Mounting Bracket Type B:

i.
B436073

Remove the 2 screws.


ii.
B436074C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and remove the front bumper extension mounting bracket as shown in the illustration.



Hide 75310A 21.REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY

a.
B449091C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the spring nut.


b.
B449093C01
0.542,0.26 0.833,0.438 false 2.031,0.26 2.417,0.406 false 0.365,0.188 0.677,0.344 0.313,0.156 10 false *a 1.823,0.167 2.135,0.323 0.313,0.156 10 false *a
*a Spring Nut


Using a screwdriver, pull out the 2 spring nuts as shown in the illustration.


c.
B449095C01
1.167,0.25 1.365,0.25 false 1.865,1.104 2.063,1.104 false 0.979,0.167 1.292,0.323 0.313,0.156 10 false *a 2.104,1.031 2.417,1.188 0.313,0.156 10 false *a
*a Cut


Using a plier nipper (side cutters), cut the 2 spring nuts at the positions shown in the illustration and remove them.


d.
B435220C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws and 2 guides as shown in the illustration to remove the radiator grille emblem assembly.


Hide 52611 22.REMOVE FRONT BUMPER ENERGY ABSORBER (for Type A)

a.
B435222C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front bumper energy absorber as shown in the illustration.


Hide 52136H 23.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (for Type B)

a.
B436076C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front energy absorber mounting reinforcement LH as shown in the illustration.


Hide 52135J 24.REMOVE FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (for Type B)

HINT:

Use the same procedure for the LH side.


Hide 52611 25.REMOVE FRONT BUMPER ENERGY ABSORBER (for Type B)

a.
B436078C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front bumper energy absorber as shown in the illustration.


Hide 52618 26.REMOVE LOWER FRONT BUMPER ABSORBER

a.
B435224

Remove the 3 clips and lower front bumper absorber.


Hide 53019B 27.REMOVE RADIATOR SHUTTER SUB-ASSEMBLY (for Type A)

Hide 53019B 28.REMOVE RADIATOR SHUTTER SUB-ASSEMBLY (for Type B)

Hide 52021 29.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type A)

a.

Disengage the 10 clamps.

B435225


b.
B435226

Remove the 8 bolts.


c.
B435227

Disengage the 2 guides to remove the front bumper reinforcement sub-assembly.


Hide 52021 30.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type B)

a.

Disengage the 11 clamps.

B436081C01
0,0 0,0 false


b.
B435226

Remove the 8 bolts.


c.
B435227

Disengage the 2 guides to remove the front bumper reinforcement sub-assembly.


Hide 52132A 31.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT

a.
B435228

Remove the 4 nuts and No. 2 front bumper reinforcement.


Hide 52113E 32.REMOVE FRONT BUMPER EXTENSION LH

a.
B435229

Remove the 4 bolts and front bumper extension LH.


Hide 52112F 33.REMOVE FRONT BUMPER EXTENSION RH

HINT:

Use the same procedure for the LH side.


Hide 52116A 34.REMOVE FRONT BUMPER SIDE SUPPORT LH

a.
B435230

Remove the bolt.


b.
B435231C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the clip as shown in the illustration.


c.
B435233C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw as shown in the illustration to remove the front bumper side support LH.


Hide 52115A 35.REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure for the LH side.