52116A
1.INSTALL FRONT BUMPER SIDE SUPPORT LH
|
Install in this Direction |
Engage the claw as shown in the illustration.
|
Install in this Direction |
Engage the clip as shown in the illustration.
Install the front bumper side support LH with the bolt.
52115A
2.INSTALL FRONT BUMPER SIDE SUPPORT RH
Use the same procedure for the LH side.
52113E
3.INSTALL FRONT BUMPER EXTENSION LH
Install the front bumper extension LH with the 4 bolts.
52112F
4.INSTALL FRONT BUMPER EXTENSION RH
Use the same procedure for the LH side.
52132A
5.INSTALL NO. 2 FRONT BUMPER REINFORCEMENT
Install the No. 2 front bumper reinforcement with the 4 nuts.
52021
6.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type A)
Engage the 2 guides.
Install the front bumper reinforcement sub-assembly with the 8 bolts.
Engage the 10 clamps.
52021
7.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY (for Type B)
Engage the 2 guides.
Install the front bumper reinforcement sub-assembly with the 8 bolts.
Engage the 11 clamps.
53019B
8.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (for Type A)
53019B
9.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (for Type B)
52618
10.INSTALL LOWER FRONT BUMPER ABSORBER
Install the lower front bumper absorber with the 3 clips.
52611
11.INSTALL FRONT BUMPER ENERGY ABSORBER (for Type A)
|
Install in this Direction |
Install the front bumper energy absorber as shown in the illustration.
52611
12.INSTALL FRONT BUMPER ENERGY ABSORBER (for Type B)
|
Install in this Direction |
Install the front bumper energy absorber as shown in the illustration.
52136H
13.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT LH (for Type B)
|
Install in this Direction |
Install the front energy absorber mounting reinforcement LH as shown in the illustration.
52135J
14.INSTALL FRONT ENERGY ABSORBER MOUNTING REINFORCEMENT RH (for Type B)
Use the same procedure for the LH side.
75310A
15.INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY
|
Install in this Direction |
Engage the 2 guides and 2 claws as shown in the illustration.
Install the radiator grille emblem assembly with 2 new spring nuts.
52114A
16.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET
for Extension Mounting Bracket Type A:
|
Install in this Direction |
Engage the 2 claws as shown in the illustration.
Install the front bumper extension mounting bracket with the 2 screws.
for Extension Mounting Bracket Type B:
|
Install in this Direction |
Engage the 2 claws as shown in the illustration.
Install the front bumper extension mounting bracket with the 2 screws.
52128B
17.INSTALL FRONT BUMPER HOLE COVER LH
| *a | Hook |
|
Install in this Direction |
Engage the hook.
Engage the 2 claws as shown in the illustration to install the front bumper hole cover LH.
52127D
18.INSTALL FRONT BUMPER HOLE COVER RH
Use the same procedure for the LH side.
53112E
19.INSTALL LOWER NO. 1 RADIATOR GRILLE
|
Install in this Direction |
Engage the 18 claws as shown in the illustration to install the lower No. 1 radiator grille.
17753
20.INSTALL NO. 3 AIR CLEANER INLET
Engage the 3 claws.
Install the No. 3 air cleaner inlet with the 2 screws.
53101
21.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
|
Install in this Direction |
Engage the 15 claws as shown in the illustration.
Install the radiator grille sub-assembly with the 2 screws and 4 clips.
53395E
22.INSTALL HOOD TO FRONT END PANEL SEAL
Remove the release paper from a new hood to front end panel seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the 2 clips and attach the double-sided tape to install the hood to front end panel seal.
|
Double-sided Tape | - | - |
53879R
23.INSTALL FRONT FENDER LINER RETAINER
Engage the 2 claws to install the 2 front fender liner retainers.
Use the same procedure for the RH side and LH side.
52113D
24.INSTALL FRONT BUMPER EXTENSION LH
Engage the claw.
Install the front bumper extension LH with the 2 screws.
52112D
25.INSTALL FRONT BUMPER EXTENSION RH
Use the same procedure for the LH side.
81220
26.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
81210A
27.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)
Use the same procedure for the LH side.
88211B
28.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
82113
29.INSTALL NO. 3 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
w/o Fog Light:
Engage the 10 clamps to install the No. 3 engine room wire.
w/ Fog Light:
Engage the 10 clamps to install the No. 3 engine room wire.
89347B
30.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89347D
31.INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89341L
32.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89341K
33.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89348J
34.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)
89341M
35.INSTALL FRONT SIDE ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)