Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM3210E _57 Power Source / Network _047550 NETWORKING _0242017 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Hybrid vehicle control ECU

·

Central gateway ECU (network gateway ECU)

·

Inverter with converter assembly

·

ECM

·

Brake booster with master cylinder assembly

·

No. 2 CAN junction connector



WIRING DIAGRAM

C346812E06
3.01,7.573 4.26,7.99 1.25,0.417 10 false No. 2 CAN Junction Connector 4.01,1.781 4.167,1.979 0.156,0.198 10 false 1 3.99,2.323 4.302,2.521 0.313,0.198 10 false 12 5.635,1.792 5.948,1.99 0.313,0.198 10 false 18 5.646,2.323 5.958,2.521 0.313,0.198 10 false 17 5.948,1.792 6.563,1.99 0.615,0.198 10 false CA4H 5.948,2.323 6.563,2.521 0.615,0.198 10 false CA4L 6.469,2.208 6.958,2.396 0.49,0.188 10 false 120 Ω 5.188,2.948 7.125,3.427 1.938,0.479 10 false Central Gateway ECU (Network Gateway ECU) 2.979,1.781 3.135,1.979 0.156,0.198 10 false 2 2.938,2.313 3.25,2.51 0.313,0.198 10 false 13 1.417,1.771 1.729,1.969 0.313,0.198 10 false 21 1.438,2.323 1.594,2.521 0.156,0.198 10 false 8 0.896,2.458 1.51,2.656 0.615,0.198 10 false CA1L 0.875,1.906 1.49,2.104 0.615,0.198 10 false CA1H 2.99,4.094 3.146,4.292 0.156,0.198 10 false 3 2.938,4.635 3.25,4.833 0.313,0.198 10 false 14 0.438,2.885 2.292,3.156 1.854,0.271 10 false Hybrid Vehicle Control ECU 0.448,5.198 2.594,5.542 2.146,0.344 10 false Inverter with Converter Assembly 1.427,4.104 1.583,4.302 0.156,0.198 10 false 1 1.427,4.646 1.583,4.844 0.156,0.198 10 false 7 0.854,4.24 1.469,4.438 0.615,0.198 10 false CANH 0.885,4.771 1.5,4.969 0.615,0.198 10 false CANL 2.99,6.427 3.146,6.625 0.156,0.198 10 false 4 2.948,6.969 3.26,7.167 0.313,0.198 10 false 15 0.635,7.552 1.25,7.792 0.615,0.24 10 false ECM 0.406,6.823 1.177,7.021 0.771,0.198 10 false 120 Ω 0.906,6.448 1.521,6.646 0.615,0.198 10 false CANH 0.938,6.99 1.552,7.188 0.615,0.198 10 false CANL 1.438,6.438 1.75,6.635 0.313,0.198 10 false 13 1.448,6.969 1.76,7.167 0.313,0.198 10 false 26 4.021,4.115 4.177,4.313 0.156,0.198 10 false 5 3.979,4.646 4.292,4.844 0.313,0.198 10 false 16 5.667,4.115 5.979,4.313 0.313,0.198 10 false 30 5.667,4.635 5.979,4.833 0.313,0.198 10 false 29 5.969,4.24 6.583,4.438 0.615,0.198 10 false CA2H 5.969,4.771 6.583,4.969 0.615,0.198 10 false CA2L 5.427,5.208 7.083,5.719 1.656,0.51 10 false Brake Booster with Master Cylinder Assembly 0.188,2.875 0.5,3.073 0.313,0.198 10 false F2 0.125,5.198 0.583,5.396 0.458,0.198 10 false C33 0.271,7.552 0.729,7.75 0.458,0.198 10 false A40 2.677,7.573 3.135,7.771 0.458,0.198 10 false F70 4.865,2.948 5.323,3.146 0.458,0.198 10 false F59 5.115,5.208 5.573,5.406 0.458,0.198 10 false A41

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the power switch on (IG) and wait at least approximately 52 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 20 km/h (12 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the F70 No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C349816C17
1.563,1.292 1.979,1.594 0.417,0.302 2.917,1.427 2.917,0.646 2.917,0.646 2.729,0.646 true 2.75,1.427 2.75,0.792 2.75,0.792 2.542,0.792 true 3.083,1.438 3.083,0.49 3.083,0.49 2.885,0.49 true 2.76,1.719 2.76,1.969 2.76,1.969 2.531,1.969 true 2.917,1.708 2.917,2.125 2.917,2.125 2.688,2.125 true 3.094,1.708 3.094,2.323 3.094,2.323 2.885,2.323 true 3.26,1.708 3.26,2.49 3.26,2.49 3.052,2.49 true 3.25,1.427 3.25,0.313 3.25,0.313 3.063,0.313 true 3.427,1.708 3.427,2.646 3.427,2.646 3.229,2.646 true 3.417,1.427 3.417,0.146 3.417,0.146 3.24,0.146 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.979,0.729 2.594,0.938 0.615,0.208 10 false CANH*b 1.99,1.896 2.604,2.104 0.615,0.208 10 false CANL*b 2.156,0.563 2.771,0.771 0.615,0.208 10 false CANH*c 2.156,2.063 2.771,2.271 0.615,0.208 10 false CANL*c 1.667,1.375 2.177,1.604 0.51,0.229 10 false F70 2.323,0.406 2.938,0.615 0.615,0.208 10 false CANH*d 2.333,2.25 2.948,2.458 0.615,0.208 10 false CANL*d 2.49,0.24 3.198,0.448 0.708,0.208 10 false CANH*e 2.688,0.073 3.302,0.281 0.615,0.208 10 false CANH*f 2.51,2.406 3.177,2.615 0.667,0.208 10 false CANL*e 2.708,2.573 3.323,2.74 0.615,0.167 10 false CANL*f
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Hybrid Vehicle Control ECU *d to Inverter with Converter Assembly
*e to ECM *f to Brake Booster with Master Cylinder Assembly


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F70-1 (CANH) - F70-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F70-2 (CANH) - F70-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control ECU
F70-3 (CANH) - F70-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Inverter with converter assembly
F70-4 (CANH) - F70-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
F70-5 (CANH) - F70-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECM) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F59 central gateway ECU (network gateway ECU) connector.


b.
C348627C12
1.438,0.094 1.865,0.354 0.427,0.26 0.688,1.802 0.688,0.813 0.688,0.813 0.99,0.813 true 0.698,2.125 0.698,2.844 0.698,2.844 0.979,2.844 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.552,0.177 1.865,0.375 0.313,0.198 10 false F70 1.063,0.76 1.656,0.927 0.594,0.167 10 false CANH*b 1.042,2.781 1.635,2.948 0.594,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-1 (CANH) - F70-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A40 ECM connector.


b.
C348627C13
1.49,0.385 1.917,0.646 0.427,0.26 1.313,1.833 1.313,0.823 1.313,0.823 1.604,0.823 true 1.313,2.125 1.313,2.854 1.313,2.854 1.656,2.854 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.594,0.458 1.906,0.656 0.313,0.198 10 false F70 1.656,0.76 2.25,0.927 0.594,0.167 10 false CANH*b 1.698,2.792 2.292,2.958 0.594,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-4 (CANH) - F70-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C347970C08
1.521,0.188 1.885,0.417 0.365,0.229 1.5,2.083 1.677,2.083 1.677,2.083 1.677,1.135 true 1.917,2.083 1.76,2.083 1.76,2.083 1.76,1.125 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.125,2.021 1.75,2.177 0.625,0.156 10 false CA4H 1.948,2.021 2.458,2.177 0.51,0.156 10 false CA4L 1.604,0.229 1.958,0.396 0.354,0.167 10 false F59
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F59-18 (CA4H) - F59-17 (CA4L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR