There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Main body ECU (multiplex network body ECU) ·
No. 1 headlight ECU sub-assembly LH ·
Certification ECU (smart key ECU assembly) ·
Central gateway ECU (network gateway ECU) ·
Meter circuit plate ·
Air conditioning amplifier assembly ·
Combination meter mirror ECU (w/ Headup Display System) ·
No. 3 CAN junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait at least approximately 33 seconds. Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the F71 No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Meter Circuit Plate |
| *c | to Main Body ECU (Multiplex Network Body ECU) | *d | to No. 1 Headlight ECU Sub-assembly LH |
| *e | to Air Conditioning Amplifier Assembly | *f | to Certification ECU (Smart Key ECU Assembly) |
| *g | to Central Gateway ECU (Network Gateway ECU) | *h | to Combination Meter Mirror ECU
(w/ Headup Display System) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F71-1 (CANH) - F71-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Meter circuit plate |
| F71-2 (CANH) - F71-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| F71-3 (CANH) - F71-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | No. 1 headlight ECU sub-assembly LH |
| F71-4 (CANH) - F71-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| F71-5 (CANH) - F71-16 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly) |
| F71-6 (CANH) - F71-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| F71-7 (CANH) - F71-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Combination meter mirror ECU* |
*: w/ Headup Display System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to central gateway ECU (network gateway ECU)) | B |
| NG (Line to meter circuit plate) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the F59 central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to Central Gateway ECU (Network Gateway ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-6 (CANH) - F71-17 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the F6 meter circuit plate connector.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
| *b | to Meter Circuit Plate |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-1 (CANH) - F71-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F59-15 (CA5H) - F59-16 (CA5L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG