The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet damper to the appropriate position to change the air inlet mode (fresh, recirculation/fresh, and recirculation).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1442/42 | Air Inlet Damper Control Servo Motor Circuit | Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly | ·
No. 1 blower damper servo sub-assembly ·
No. 1 air conditioning radiator damper servo sub-assembly ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly ·
Blower assembly |
Memorized
(30 sec. or more)* |
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
for Dual Type
for Single Type
Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.
When installing the damper servo motor, make sure to install it correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>REASSEMBLY
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD (for Dual Type) | A |
| for LHD (for Single Type) | B |
| for RHD (for Dual Type) | C |
| for RHD (for Single Type) | D |
A
B
C
D
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1497/97 is output | A |
| DTC B1441/41, B1442/42, B1446/46 and B1448/48 are output | B |
| DTC B1442/42 is output | C |
A
B
C
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1497/97 is output | A |
| DTC B1441/41, B1442/42 and B1448/48 are output | B |
| DTC B1442/42 is output | C |
A
B
C
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1497/97 is output | A |
| DTC B1441/41, B1442/42, B1443/43 and B1446/46 are output | B |
| DTC B1442/42 is output | C |
A
B
C
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1497/97 is output | A |
| DTC B1441/41, B1442/42 and B1443/43 are output | B |
| DTC B1442/42 is output | C |
A
B
C
Remove the No. 1 blower damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY
Operate the air inlet control dampers by hand.
The air inlet control dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.
Disconnect the No. 1 blower damper servo sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6 (STE2) - 3 (sigB) | Always | Below 1 Ω |
| 5 (STE1) - 2 (sigA) | Always | Below 1 Ω |
| 8 (M-) - 5 (M-) | Always | Below 1 Ω |
| 7 (M+) - 4 (M+) | Always | Below 1 Ω |
| 4 (GND) - 1 (GND) | Always | Below 1 Ω |
| 6 (STE2) or 3 (sigB) - Body ground | Always | 10 kΩ or higher |
| 5 (STE1) or 2 (sigA) - Body ground | Always | 10 kΩ or higher |
| 8 (M-) or 5 (M-) - Body ground | Always | 10 kΩ or higher |
| 7 (M+) or 4 (M+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.
Remove the No. 3 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Connect the No. 1 blower damper servo sub-assembly connector to the No. 3 air conditioning radiator damper servo sub-assembly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet Damper Targ Pulse | No. 1 blower damper servo sub-assembly pulse* | Min.: 128
Max.: 383 |
Operates between 220 to 256 pulses |
*: Thus this Active Test is for the No. 1 blower damper servo sub-assembly, in this case it is used to check the operation of the No. 3 air conditioning radiator damper servo sub-assembly.
| Tester Display |
|---|
| Air Inlet Damper Targ Pulse |
The No. 3 air conditioning radiator damper servo sub-assembly operates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG