Home › Brake › BRAKE (REAR) › REAR BRAKE
RM3210E _54 Brake _047537 BRAKE (REAR) _0244653 REAR BRAKE A

BRAKE (REAR)  REAR BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be stored. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C349638C01
1.823,1.01 2.698,0.979 2.698,0.979 1.802,0.948 true 2.75,0.906 3.063,1.063 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 47722A 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 47775D 3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C211756C01
1.865,1.406 1.854,1.406 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.
C349636

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 47835 4.INSTALL REAR DISC BRAKE PAD GUIDE PIN

a.
C318775C02
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the 2 rear disc brake pad guide pins.


b.

Install a new rear disc brake cylinder slide bushing to each rear disc brake pad guide pin.


c.
C211758C04
1.25,0.938 1.25,0.927 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the 2 rear disc brake pad guide pins.


d.
C363537

Install the 2 rear disc brake pad guide pins to rear disc brake cylinder mounting.


e.

Push the 2 rear disc brake pad guide pins into the 2 rear disc brake bushing dust boots to engage the pins to the boots.


Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.
C350149

Install the 2 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 04946 6.INSTALL REAR DISC BRAKE ANTI SQUEAL SHIM KIT

NOTICE:
·

When replacing worn rear disc brake pads and rear disc brake anti-squeal shims must be replaced together with the rear disc brake pads.

·

Do not apply disc brake grease to the lining surface of the brake pad.

·

Install the rear disc brake anti-squeal shims in the correct positions and directions.



a.
C275018C03
0.708,0.292 1.052,0.51 0.344,0.219 12 false *a 0.74,1.771 1.094,2.01 0.354,0.24 12 false *b
*a Inner
*b Outer
V100145

Disc Brake Grease


Apply disc brake grease to the back plate of the rear disc brake pads.


b.
C348721C02
0.448,1.365 0.448,0.99 false 0.823,1.594 0.823,1.219 false 1.385,2.021 1.385,1.646 false 1.896,2.313 1.896,1.938 false 2.552,2.698 2.552,2.323 false 3.073,2.917 3.073,2.542 false 1.302,2.063 1.615,2.219 0.313,0.156 10 false *1 0.719,1.635 1.031,1.792 0.313,0.156 10 false *2 0.365,1.396 0.677,1.552 0.313,0.156 10 false *3 1.802,2.344 2.115,2.5 0.313,0.156 10 false *1 2.479,2.729 2.792,2.885 0.313,0.156 10 false *2 2.979,2.938 3.292,3.094 0.313,0.156 10 false *3
*1 Rear Disc Brake Pad
*2 Rear No. 1 Disc Brake Anti-squeal Shim
*3 Rear No. 2 Disc Brake Anti-squeal Shim


Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.


Hide 04466 7.INSTALL REAR DISC BRAKE PAD KIT

a.
C349633

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the disc brake pads or the rear disc.



Hide 8.INSTALL ANTI SQUEAL SPRING

a.
C349632

Install the 2 anti-squeal springs to the rear disc brake pads.

NOTICE:
·

When replacing the rear disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the rear disc brake pad installation holes as far as they will go.




Hide 47850 9.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C350148N01
1.26,1.875 2.104,1.875 true 2.135,1.802 2.594,2 0.458,0.198 10 false SST 1.031,3.302 1.313,3.479 0.281,0.177 10 true 90°

To compensate for pad lining thickness, use SST to adjust the protrusion of the rear disc brake piston by turning it.

SST
09719-12010  (09719-01030)

NOTICE:
·

Place the disc between the 2 brake pads and determine the piston return value.

·

Turn the rear disc brake piston to the position where the protrusion on the rear disc brake pad lines up properly with the piston groove.




b.

Hold the 2 rear disc brake pad guide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the rear disc brake cylinder assembly while holding both of the rear disc brake pads because the anti-squeal springs may fall off the rear disc brake pads.

·

Be sure that the anti-squeal springs are installed to the rear disc brake pads.




Hide 47319F 10.CONNECT REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
33.3 N*m (340 kgf*cm, 25 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 46430 11.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C345983C03
1.948,2.979 2.417,2.979 false 1.885,2.177 2.188,2.177 2.188,2.177 2.313,2.365 false 1.708,2.115 2.021,2.271 0.313,0.156 10 false *a 1.76,2.917 2.073,3.073 0.313,0.156 10 false *1
*1 Rear Disc Brake Cylinder Assembly
*a Clip


Engage the clip to install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

NOTICE:

Be sure to engage the clip to the rear disc brake cylinder assembly as shown in the illustration.



b.
C345984

Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.


c.
C345058

Install the No. 3 parking brake cable assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


Hide 47658B 12.INSTALL PARKING BRAKE LEVER PROTECTOR

Hide 13.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

a.

Connect the reservoir level switch connector.


b.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


c.

Perform the following procedure if air bleeding is not necessary:

i.

Turn the power switch on (READY).


ii.

Depress the brake pedal and release it.




Hide 14.BLEED BRAKE LINE

Hide 15.ADJUST PARKING BRAKE

Hide 16.INSTALL REAR WHEEL