Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM
RM3210E _58 Vehicle Interior _047507 THEFT DETERRENT / KEYLESS ENTRY _0244661 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered to the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ID code box (immobiliser code ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:

If a immobiliser system or hybrid control system DTC is output, first perform troubleshooting for the immobiliser system or hybrid control system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS

B

2.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts within 5 seconds of the power switch being turned on (READY).

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI AND IMO)
3.CHECK HYBRID VEHICLE CONTROL ECU (TERMINAL IMI AND IMO)
a.

Using an oscilloscope, check the waveform.

B412489C06
5.208,0.188 5.604,0.427 0.396,0.24 4.292,2.01 4.542,2.01 4.542,2.01 5,1.052 true 5.063,1.167 5.406,2 5.406,2 5.625,2 true 5.323,0.219 5.781,0.417 0.458,0.198 10 false F3 4.073,1.938 4.531,2.135 0.458,0.198 10 false IMI 5.698,1.917 6.156,2.115 0.458,0.198 10 false IMO 1.021,3.604 1.479,3.802 0.458,0.198 10 false GND 1.042,5.646 1.5,5.844 0.458,0.198 10 false GND 3,2.646 3.458,2.844 0.458,0.198 10 false *g 2.938,3.688 3.396,3.885 0.458,0.198 10 false *b 3.125,3.688 3.583,3.885 0.458,0.198 10 false *c 3.333,5.76 3.792,5.958 0.458,0.198 10 false *b 3.51,5.75 3.969,5.948 0.458,0.198 10 false *c 2.396,4.635 2.854,4.833 0.458,0.198 10 false *f 3.438,4.646 3.896,4.844 0.458,0.198 10 false *h 1.479,6.49 1.938,6.688 0.458,0.198 10 false *i 3.229,6.49 3.688,6.688 0.458,0.198 10 false *i 1.854,7.115 2.313,7.313 0.458,0.198 10 false *d 3.74,7.094 4.198,7.292 0.458,0.198 10 false *d 1.927,7.385 2.385,7.583 0.458,0.198 10 false *e 3.646,7.365 4.104,7.563 0.458,0.198 10 false *e 0.125,0.104 0.583,0.302 0.458,0.198 10 false *a
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f Waveform 1
*g Waveform 2 *h Waveform 3
*i Waveform 1 (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
F3-23 (IMO) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 2)
F3-10 (IMI) - Body ground Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1 and 3)



Result:
Result Proceed to
Normal waveform A
Waveform 1 is not output, or has abnormal wavelength or shape B
Waveform 2 is not output, or has abnormal wavelength or shape C
Waveform 3 is not output, or has abnormal wavelength or shape D



A

4.REGISTER ECU COMMUNICATION ID

B

6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)

C

D

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
4.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
5.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID WAS NOT REGISTERED)

NG

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
6.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the F19 ID code box (immobiliser code ECU) connector.


b.

Disconnect the F3 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-3 (EFII) - F3-23 (IMO) Always Below 1 Ω
F19-3 (EFII) or F3-23 (IMO) - Body ground Always 10 kΩ or higher
F19-4 (EFIO) - F3-10 (IMI) Always Below 1 Ω
F19-4 (EFIO) or F3-10 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER RECOGNITION CODE
8.REGISTER RECOGNITION CODE
a.

Register the recognition codes to the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID codes.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
10.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS
a.

Check that the hybrid control system starts.

OK:

Hybrid control system starts normally.



Result:
Proceed to
OK
NG



OK

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

NG