This DTC is stored when there is an open or short circuit in the communication line between the front side sensors and the ECU, or when there is a malfunction in a front side sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AEE | IPA Sensor Communication Circuit | An open or short circuit in the communication line between the front side sensors and ECU or a malfunction in a front side sensor during initialization mode after the power switch is turned on (IG). | ·
Front side ultrasonic sensor circuit ·
Harness or connector ·
Clearance warning ECU assembly |
Check for DTCs.
Clear the DTCs.
Recheck for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEE is output | A |
| No DTCs are output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the F26 clearance warning ECU assembly connector.
Disconnect the B5 front side ultrasonic sensor LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F26-2 (CSB1) - B5-4 (BI) | Always | Below 1 Ω |
| F26-7 (LIN1) - B5-5 (SI) | Always | Below 1 Ω |
| F26-5 (CSG1) - B5-6 (EI) | Always | Below 1 Ω |
| F26-2 (CSB1) or B5-4 (BI) - Body ground | Always | 10 kΩ or higher |
| F26-7 (LIN1) or B5-5 (SI) - Body ground | Always | 10 kΩ or higher |
| F26-5 (CSG1) or B5-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B6 front side ultrasonic sensor RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B5-1 (BO) - B6-4 (BI) | Always | Below 1 Ω |
| B5-2 (SO) - B6-5 (SI) | Always | Below 1 Ω |
| B5-3 (EO) - B6-6 (EI) | Always | Below 1 Ω |
| B5-1 (BO) or B6-4 (BI) - Body ground | Always | 10 kΩ or higher |
| B5-2 (SO) or B6-5 (SI) - Body ground | Always | 10 kΩ or higher |
| B5-3 (EO) or B6-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front Side Ultrasonic Sensor LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (BI) - 6 (EI) | Always | 10 kΩ or higher |
| 4 (BI) - 1 (BO) | Always | Below 1 Ω |
| 5 (SI) - 2 (SO) | Always | Below 30 Ω |
| 6 (EI) - 3 (EO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front Side Ultrasonic Sensor RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (BI) - 6 (EI) | Always | 10 kΩ or higher |
| 4 (BI) - 1 (BO) | Always | Below 1 Ω |
| 5 (SI) - 2 (SO) | Always | Below 30 Ω |
| 6 (EI) - 3 (EO) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE0
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEE is output | A |
| No DTCs are output | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>C1AE5
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1AEE is output | A |
| No DTCs are output | B |
A
B