Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3210E _56 Audio / Visual / Telematics _047512 PARK ASSIST / MONITORING _0244875 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AC1  Master Module Horizontal Axis Misalignment  


DESCRIPTION

This DTC is stored when the angle of the blind spot monitor sensor LH deviates more than the allowable range from the horizontal axis.

HINT:
·

If a drum tester such as a speedometer tester, brake/speedometer combination tester or chassis dynamometer is used with the blind spot monitor system on, the blind spot monitor sensor may store this DTC by mistake.

·

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.



DTC No. Detection Item DTC Detection Condition Trouble Area
C1AC1 Master Module Horizontal Axis Misalignment When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is activated Blind spot monitor sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Check the condition of the rear bumper around the blind spot monitor sensors.

HINT:

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.


Result:
Result Proceed to
A sticker, mud, snow, ice, etc. is covering the sensor or surrounding area on the rear bumper. A
There are scratches or dents on the rear bumper around the sensors. B
No abnormalities.




A

2.PERFORM BEAM AXIS CONFIRMATION

B

3.CHECK INSTALLATION CONDITION
2.PERFORM BEAM AXIS CONFIRMATION
a.

Clean the rear bumper.


b.

Perform Blind Spot Monitor Beam Axis Confirmation using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 5238
Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 5231

Result:
Proceed to
OK
NG



OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR LH

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL

NOTICE:

Before replacing the blind spot monitor sensor LH, visually check for damage to the stud bolts or area surrounding the blind spot monitor sensor LH.

If there is any damage to the stud bolts or area surrounding the blind spot monitor sensor LH, perform Blind Spot Monitor Sensor Installation Condition Inspection and adjust according to the result.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK



3.CHECK INSTALLATION CONDITION
a.

Check the installation condition of the blind spot monitor sensor LH.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

HINT:

Take the appropriate action in accordance with the result.



Result:
Proceed to
NEXT



NEXT

4.PERFORM BEAM AXIS CONFIRMATION
4.PERFORM BEAM AXIS CONFIRMATION

b.

Perform Blind Spot Monitor Beam Axis Confirmation using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Display
50005 313 5238
Body Electrical > Blind Spot Monitor Master > Utility
Tester Display
BSM Master Beam Axis Adjustment
50005 313 5231

Result:
Proceed to
OK
NG



OK

END

NG