The hybrid vehicle control ECU communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the hybrid vehicle control ECU stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P162B87 | Lost Communication with Battery Monitor Module Missing Message | Battery state sensor assembly or hybrid vehicle control ECU communication stops for approximately 17 minutes or more with the power switch on (IG)
(1 trip detection logic) |
·
Wire harness or connector ·
Battery state sensor assembly ·
Hybrid vehicle control ECU |
Charge warning light does not come on | DTC stored |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.
Check installation condition of the battery state sensor assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the battery state sensor assembly connector is securely connected.
The connector is securely connected.
Disconnect the C19 battery state sensor assembly connector.
Check the connector case and terminals for deformation or corrosion.
No deformation or corrosion.
| *a | Front view of wire harness connector
(to Battery State Sensor Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C19-1 (+B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A50 hybrid vehicle control ECU connector.
Disconnect the C19 battery state sensor assembly connector.
Disconnect the C12 compressor with motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A50-8 (LIN3) - C19-2 (LIN) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C19-2(LIN), A50-8 (LIN3) or C12-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs, and note down any DTCs that are output.
Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs.
Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
Check for DTCs, and note down any DTCs that are output.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
Clear the DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (READY) and wait for 17 minutes or more.
Turn the GTS on.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
Click herePower Source / Network>2ZR-FXE BATTERY / CHARGING>CHARGING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC P162B87 is output. | A |
| DTCs are not output. | B |
A
B
Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
Check for DTCs when the following conditions are met.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1498/98 is output. | A |
| DTCs are not output. | B |
A
B