Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, also the navigation receiver assembly itself will not function.

WIRING DIAGRAM

E334508E01
4.469,0.479 4.781,0.677 0.313,0.198 10 false z3 4.469,1.594 4.781,1.792 0.313,0.198 10 false z3 4.479,2.698 4.792,2.896 0.313,0.198 10 false z3 5.438,2.708 5.75,2.906 0.313,0.198 10 false F21 5.427,1.604 5.74,1.802 0.313,0.198 10 false F21 5.427,0.49 5.74,0.688 0.313,0.198 10 false F21 5.5,0.292 5.813,0.49 0.313,0.198 10 false 6 5.51,1.396 5.823,1.594 0.313,0.198 10 false 3 5.49,2.51 5.802,2.708 0.313,0.198 10 false 5 4.458,2.51 4.771,2.708 0.313,0.198 10 false 10 4.49,1.406 4.802,1.604 0.313,0.198 10 false 8 4.458,0.292 4.771,0.49 0.313,0.198 10 false 11 6.042,2.583 6.354,2.781 0.313,0.198 10 false 22 6.031,1.479 6.344,1.677 0.313,0.198 10 false 23 6.042,0.385 6.354,0.583 0.313,0.198 10 false 21 6.292,1.594 6.771,1.813 0.479,0.219 10 false SWG 6.302,0.469 6.781,0.688 0.479,0.219 10 false SW1 6.292,2.688 6.771,2.906 0.479,0.219 10 false SW2 4.906,2.594 5.219,2.792 0.313,0.198 10 false AU2 4.906,1.479 5.219,1.677 0.313,0.198 10 false EAU 4.917,0.365 5.229,0.563 0.313,0.198 10 false AU1 4.188,3.135 5.719,3.688 1.531,0.552 10 false Spiral Cable with Sensor Sub-assembly 5.875,3.25 7.104,3.823 1.229,0.573 10 false Navigation Receiver Assembly 5.885,3.104 6.198,3.302 0.313,0.198 10 false F92 1.104,3.177 3.781,3.448 2.677,0.271 10 false Steering Pad Switch Assembly 0.552,1.031 1.25,1.24 0.698,0.208 10 false Volume- 1.302,1.031 2,1.24 0.698,0.208 10 false Volume+ 2.104,1.021 2.802,1.229 0.698,0.208 10 false Seek- 2.729,1.01 3.427,1.219 0.698,0.208 10 false Seek+ 2.719,2.125 3.417,2.333 0.698,0.208 10 false MODE 2.021,2.125 2.719,2.333 0.698,0.208 10 false On hook 1.333,2.125 2.031,2.333 0.698,0.208 10 false Off hook 0.677,2.125 1.375,2.333 0.698,0.208 10 false Voice

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-21 (SW1) - F92-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
F92-22 (SW2) - F92-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY