Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E334510E01
0.271,2.406 2.198,2.646 1.927,0.24 10 false Steering Pad Switch Assembly 2.385,2.042 3.896,2.427 1.51,0.385 10 false Spiral Cable with Sensor Sub-assembly 2.958,0.948 3.313,1.156 0.354,0.208 10 false IL+2 2.49,1.052 2.844,1.26 0.354,0.208 10 false z3 2.49,1.615 2.844,1.823 0.354,0.208 10 false z3 2.521,0.844 2.74,1.021 0.219,0.177 10 false 5 3.521,1.052 3.875,1.26 0.354,0.208 10 false F21 3.521,1.615 3.875,1.823 0.354,0.208 10 false F21 3.552,0.844 3.771,1.021 0.219,0.177 10 false 13 2.969,1.51 3.323,1.719 0.354,0.208 10 false EAU 2.521,1.406 2.74,1.583 0.219,0.177 10 false 8 3.594,1.406 3.813,1.583 0.219,0.177 10 false 3 4.24,0.448 4.75,0.667 0.51,0.219 10 false PANEL 2.417,0.281 3.438,0.5 1.021,0.219 10 false from TAIL Relay 5.729,1.052 6.083,1.26 0.354,0.208 10 false F93 5.781,0.854 6,1.031 0.219,0.177 10 false 10 6.104,1.052 6.458,1.26 0.354,0.208 10 false ILL+ 5.74,1.615 6.094,1.823 0.354,0.208 10 false F92 5.792,1.417 6.01,1.594 0.219,0.177 10 false 23 6.104,1.615 6.542,1.844 0.438,0.229 10 false SWG 5.74,2.177 6.094,2.385 0.354,0.208 10 false F94 6.104,2.177 6.542,2.385 0.438,0.208 10 false ILL- 5.823,1.969 6.042,2.146 0.219,0.177 10 false 5 5.906,2.552 7.094,2.927 1.188,0.375 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F21 spiral cable with sensor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F21-13 (IL+2) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Remove the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F93 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F93-10 (ILL+) - Body ground Power switch off
Light control switch in tail or head position
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)
a.

Disconnect the F94 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F94-5 (ILL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR