Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Microphone Circuit between Microphone and Navigation Receiver Assembly  


DESCRIPTION

The navigation receiver assembly and telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2, and the telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 sends microphone signals to the navigation receiver assembly.

*1: w/o Sliding Roof

*2: w/ Sliding Roof


WIRING DIAGRAM

E334512E01
0.844,0.646 1.458,0.844 0.615,0.198 10 false MACC 0.844,1.063 1.458,1.26 0.615,0.198 10 false MCO+ 0.865,1.49 1.479,1.688 0.615,0.198 10 false MCO- 0.885,2.313 1.5,2.51 0.615,0.198 10 false SNS2 1.333,0.542 1.688,0.719 0.354,0.177 10 false 17*2 1.406,0.385 1.76,0.563 0.354,0.177 10 false 1*1 1.333,0.958 1.688,1.135 0.354,0.177 10 false 16*2 1.406,0.802 1.76,0.979 0.354,0.177 10 false 2*1 1.333,1.375 1.688,1.552 0.354,0.177 10 false 15*2 1.406,1.219 1.76,1.396 0.354,0.177 10 false 4*1 1.344,2.208 1.698,2.385 0.354,0.177 10 false 14*2 1.417,2.042 1.771,2.219 0.354,0.177 10 false 3*1 0.125,3.292 0.479,3.469 0.354,0.177 10 false O4*2 0.125,2.698 0.479,2.875 0.354,0.177 10 false O2*1 0.135,2.865 2.375,3.094 2.24,0.229 10 false Telephone Microphone Assembly*1 0.125,3.448 3.781,3.677 3.656,0.229 10 false Map Light Assembly (Telephone Microphone Assembly)*2 3.281,1.75 3.927,1.969 0.646,0.219 10 false (Shielded) 5.938,0.656 6.552,0.854 0.615,0.198 10 false MACC 5.938,1.073 6.552,1.271 0.615,0.198 10 false MIN+ 5.938,1.49 6.552,1.688 0.615,0.198 10 false MIN- 5.938,1.906 6.552,2.104 0.615,0.198 10 false SGND 5.938,2.323 6.552,2.521 0.615,0.198 10 false SNS2 5.76,0.542 5.969,0.74 0.208,0.198 10 false 4 5.76,0.958 5.969,1.156 0.208,0.198 10 false 5 5.688,1.375 5.896,1.573 0.208,0.198 10 false 19 5.688,1.792 5.896,1.99 0.208,0.198 10 false 18 5.75,2.208 5.958,2.406 0.208,0.198 10 false 6 5.719,2.708 6.073,2.885 0.354,0.177 10 false F92 5.708,2.875 6.917,3.24 1.208,0.365 10 false Navigation Receiver Assembly 1.396,3.885 2.677,4.094 1.281,0.208 10 false *1: w/o Sliding Roof 1.396,4.313 2.677,4.521 1.281,0.208 10 false *2: w/ Sliding Roof

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.


c.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

Voice can be recorded for up to 5 seconds.




d.

Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

OK:

All check results are normal.



Result:
Result Proceed to
OK A
NG (w/o Sliding Roof) B
NG (w/ Sliding Roof) C



A

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

C

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the O2 telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-4 (MACC) - O2-1 (MACC) Always Below 1 Ω
F92-5 (MIN+) - O2-2 (MCO+) Always Below 1 Ω
F92-19 (MIN-) - O2-4 (MCO-) Always Below 1 Ω
F92-6 (SNS2) - O2-3 (SNS2) Always Below 1 Ω
F92-4 (MACC) or O2-1 (MACC) - Body ground Always 10 kΩ or higher
F92-5 (MIN+) or O2-2 (MCO+) - Body ground Always 10 kΩ or higher
F92-19 (MIN-) or O2-4 (MCO-) - Body ground Always 10 kΩ or higher
F92-18 (SGND) - Body ground Always 10 kΩ or higher
F92-6 (SNS2) or O2-3 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the O4 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-4 (MACC) - O4-17 (MACC) Always Below 1 Ω
F92-5 (MIN+) - O4-16 (MCO+) Always Below 1 Ω
F92-19 (MIN-) - O4-15 (MCO-) Always Below 1 Ω
F92-6 (SNS2) - O4-14 (SNS2) Always Below 1 Ω
F92-4 (MACC) or O4-17 (MACC) - Body ground Always 10 kΩ or higher
F92-5 (MIN+) or O4-16 (MCO+) - Body ground Always 10 kΩ or higher
F92-19 (MIN-) or O4-15 (MCO-) - Body ground Always 10 kΩ or higher
F92-18 (SGND) - Body ground Always 10 kΩ or higher
F92-6 (SNS2) or O4-14 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E289390C23
1.521,0.698 1.896,0.938 0.375,0.24 2.552,2.531 2.198,1.958 false 2.208,1.792 2.365,0.99 false 2.063,2.771 2.063,1.969 false 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 1.594,0.729 1.906,0.927 0.313,0.198 10 false F92 2.333,0.802 2.854,1.01 0.521,0.208 10 false MACC 2.542,2.552 3.063,2.76 0.521,0.208 10 false SGND 2.01,2.802 2.531,3.01 0.521,0.208 10 false MIN-
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F92-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-18 (SGND) - Body ground Always Below 1 Ω
F92-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/o Sliding Roof) A
OK (w/ Sliding Roof) B
NG C



A

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY

B

7.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

C

5.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Remove the telephone microphone assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E221776C03
1.375,1.583 1.625,1.229 false 2,1.583 1.792,1.24 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.073,1.604 1.479,1.802 0.406,0.198 10 false MCO- 1.979,1.615 2.385,1.813 0.406,0.198 10 false SNS2
*a Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE TELEPHONE MICROPHONE ASSEMBLY

6.INSPECT TELEPHONE MICROPHONE ASSEMBLY
a.

Turn the power switch on (ACC).


b.
E279075C04
0.542,2.125 0.958,2.375 0.417,0.25 1.594,2.073 1.99,1.375 false 1.594,2.323 1.958,2.719 false 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.667,2.177 0.979,2.375 0.313,0.198 10 false O2 1.979,1.188 2.479,1.385 0.5,0.198 10 false MCO+ 1.927,2.74 2.427,2.938 0.5,0.198 10 false MCO-
*a Component with harness connected
(Telephone Microphone Assembly)


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the O2 telephone microphone assembly connector.


c.

Check the waveform of the telephone microphone assembly using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output. A
A waveform synchronized with the voice input to the telephone microphone assembly is not output. B




A

B

REPLACE TELEPHONE MICROPHONE ASSEMBLY

7.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E187117C67
2.031,1.698 1.885,1.375 false 1.604,1.688 1.771,1.375 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.021,1.719 2.635,1.917 0.615,0.198 10 false SNS2 1.281,1.708 1.896,1.906 0.615,0.198 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
14 (SNS2) - 15 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

9.REPLACE TELEPHONE MICROPHONE ASSEMBLY
8.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Turn the power switch on (ACC).


b.
E187122C70
1.49,0.542 1.906,0.792 0.417,0.25 1.24,2.865 1.656,2.219 false 1.781,2.208 2.115,2.833 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 0.854,2.865 1.333,3.063 0.479,0.198 10 false MCO+ 2.125,2.854 2.729,3.031 0.604,0.177 10 false MCO- 1.615,0.594 1.948,0.76 0.333,0.167 10 false O4
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 16 (MCO+) and 15 (MCO-) of the O4 map light assembly (telephone microphone assembly) connector.


c.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

9.REPLACE TELEPHONE MICROPHONE ASSEMBLY
9.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL


b.

Check if the same malfunction recurs.

Result:
Result Proceed to
Malfunction does not recur (returns to normal). A
Malfunction recurs. B




A

END

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)