Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type)
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0245074 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E336503E06
1.25,1.031 1.865,1.229 0.615,0.198 10 false MUTE 1.729,0.917 2.344,1.115 0.615,0.198 10 false 1 5.292,0.917 5.906,1.115 0.615,0.198 10 false 16 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUT1 0.677,1.906 1.292,2.104 0.615,0.198 10 false F61 0.667,2.052 1.875,2.521 1.208,0.469 10 false Stereo Component Amplifier Assembly 5.333,2.063 6.542,2.552 1.208,0.49 10 false Navigation Receiver Assembly 5.333,1.906 5.948,2.104 0.615,0.198 10 false F92

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C50
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.604,0.844 1.938,1 0.333,0.156 10 false F61 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F61-1 (MUTE) - Body ground Power switch on (ACC)
Audio system playing
→ Audio system changing modes
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F92 navigation receiver assembly connector.


b.

Disconnect the F61 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F92-16 (MUT1) - F61-1 (MUTE) Always Below 1 Ω
F92-16 (MUT1) or F61-1 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the F92 navigation receiver assembly connector.


b.
E265411C26
1.5,0.5 1.938,0.781 0.438,0.281 0.854,2.542 0.979,2.094 false 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.594,0.542 2.24,0.885 0.646,0.344 10 false F92 0.688,2.594 1.333,2.854 0.646,0.26 10 false MUT1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F92-16 (MUT1) - Body ground Power switch on (ACC)
Audio system playing
2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY