Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1247  Stroke Sensor  C1392  Zero Point Calibration of Stroke Sensor undone  


DESCRIPTION

The brake pedal stroke sensor assembly sends a signal about the pedal stroke to the skid control ECU (brake booster with master cylinder assembly).

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1247 Stroke Sensor 211
212
213
214
215
216
217
·

INF Code: 211

·

The sensor supply voltage (VCSK) is 4.7 V or less, or 5.3 V or more for 0.2 seconds or more.


·

INF Code: 212

·

The sensor output voltage 1 (SKS1) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.


·

INF Code: 213

·

The sensor output voltage 2 (SKS2) is less than 0.3 V, or 4.7 V or more for 0.2 seconds or more.


·

INF Code: 214

·

The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more.


·

INF Code: 215

·

The difference between the current value and previous value of the sensor output voltage 2 (SKS2) is 8.5% or more for 0.2 seconds or more.


·

INF Code: 216

·

The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more.

(The comparison value of SKS1 and SKS2 is invalid.)


·

INF Code: 217

·

Sensor data is invalid for 0.2 seconds or more.

(The sensor data of SKS1 and SKS2 is invalid.)



·

INF Code: 211

·

Open or short in brake pedal stroke sensor assembly power supply circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Skid control ECU (brake booster with master cylinder assembly)


·

INF Code: 212, 213, 214, 215, 216, 217

·

Open or short in wire harness

·

Improperly connected connector, deformation or corrosion of terminals

·

Brake pedal stroke sensor assembly



Electronically controlled brake system DTC
C1392 Zero Point Calibration of Stroke Sensor undone 1124 The brake pedal stroke sensor assembly zero point calibration is not performed.
(Normal brake pedal stroke sensor assembly zero point not memorized.)
Normal brake pedal stroke sensor assembly zero point not memorized.
(Linear solenoid valve offset learning is not performed or Test Mode is not performed or not complete.)
Electronically controlled brake system DTC
HINT:

During test mode, related DTCs are cleared.



WIRING DIAGRAM

C345754E02
4.646,0.552 4.958,0.75 0.313,0.198 10 false 25 4.917,0.771 5.385,1.01 0.469,0.24 10 false VSK1 4.656,1.167 4.969,1.365 0.313,0.198 10 false 17 4.927,1.385 5.385,1.615 0.458,0.229 10 false SKS1 4.646,1.781 4.958,1.979 0.313,0.198 10 false 13 4.906,2 5.406,2.292 0.5,0.292 10 false SKG1 4.656,2.292 4.969,2.49 0.313,0.198 10 false 21 4.906,2.521 5.385,2.781 0.479,0.26 10 false VSK2 4.646,2.917 4.958,3.115 0.313,0.198 10 false 19 4.896,3.125 5.365,3.396 0.469,0.271 10 false SKS2 4.646,3.521 4.958,3.719 0.313,0.198 10 false 33 4.896,3.74 5.417,4.021 0.521,0.281 10 false SKG2 6.375,2.104 6.688,2.302 0.313,0.198 10 false IC 4.813,4.094 5.125,4.292 0.313,0.198 10 false A41 4.823,4.26 6.885,4.656 2.063,0.396 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 2.865,0.563 3.177,0.76 0.313,0.198 10 false 4 2.865,1.177 3.177,1.375 0.313,0.198 10 false 6 2.865,1.792 3.177,1.99 0.313,0.198 10 false 5 2.865,2.302 3.177,2.5 0.313,0.198 10 false 2 2.865,2.927 3.177,3.125 0.313,0.198 10 false 1 2.865,3.531 3.177,3.729 0.313,0.198 10 false 3 0.458,4.104 0.771,4.302 0.313,0.198 10 false A45 0.458,4.281 2.917,4.646 2.458,0.365 10 false Brake Pedal Stroke Sensor Assembly 0.74,1.198 0.99,1.531 0.25,0.333 10 false Hall IC1 0.74,2.938 1,3.344 0.26,0.406 10 false Hall IC2 2.375,0.771 2.844,1.01 0.469,0.24 10 false VCSK 2.417,1.396 2.875,1.625 0.458,0.229 10 false SKS1 2.458,2 2.958,2.292 0.5,0.292 10 false SKG 2.396,2.51 2.875,2.771 0.479,0.26 10 false VSK2 2.396,3.135 2.865,3.406 0.469,0.271 10 false SKS2 2.385,3.76 2.906,4.042 0.521,0.281 10 false SKG2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake pedal stroke sensor assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.


b.

Check and adjust the brake pedal height.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT



Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Disconnect the A45 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-13 (SKG1) - A45-5 (SKG) Always Below 1 Ω
A41-13 (SKG1) or A45-5 (SKG) - Body ground Always 10 kΩ or higher
A41-17 (SKS1) - A45-6 (SKS1) Always Below 1 Ω
A41-17 (SKS1) or A45-6 (SKS1) - Body ground Always 10 kΩ or higher
A41-19 (SKS2) - A45-1 (SKS2) Always Below 1 Ω
A41-19 (SKS2) or A45-1 (SKS2) - Body ground Always 10 kΩ or higher
A41-21 (VSK2) - A45-2 (VSK2) Always Below 1 Ω
A41-21 (VSK2) or A45-2 (VSK2) - Body ground Always 10 kΩ or higher
A41-25 (VSK1) - A45-4 (VCSK) Always Below 1 Ω
A41-25 (VSK1) or A45-4 (VCSK) - Body ground Always 10 kΩ or higher
A41-33 (SKG2) - A45-3 (SKG2) Always Below 1 Ω
A41-33 (SKG2) or A45-3 (SKG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C156491C42
0.323,1.156 0.677,1.396 0.354,0.24 1.573,2.313 1.365,2.927 true 0.729,2.823 1.396,2.292 true 1.802,2.313 2.021,2.938 true 2.833,2.896 1.979,2.302 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *a 0.375,1.188 0.688,1.385 0.313,0.198 10 false A45 2.76,2.917 3.198,3.146 0.438,0.229 10 false SKG 1.917,2.99 2.354,3.229 0.438,0.24 10 false VCSK 1.219,2.979 1.635,3.188 0.417,0.208 10 false SKG2 0.563,2.854 1.031,3.094 0.469,0.24 10 false VSK2
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)


Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A45-4 (VCSK) - A45-5 (SKG) Power switch on (IG) 4.84 to 5.16 V
A45-2 (VSK2) - A45-3 (SKG2) Power switch on (IG) 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY