Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM3210E _54 Brake _047516 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0245157 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1425  Open in Stop Switch Circuit  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1425 Open in Stop Switch Circuit 231 An open stop light switch circuit continues for 10 seconds or more.
·

Wire harness or connector (refer to "Open Detection Area")

·

Stop light switch assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC

WIRING DIAGRAM

w/ Canister Pump Module:
C353687E02
5.052,3.854 5.51,4.052 0.458,0.198 10 false A41 5.042,4.042 7.104,4.469 2.063,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.208,2.979 5.063,3.344 0.854,0.365 10 false to Stop Light Circuit 5.292,1.906 5.75,2.104 0.458,0.198 10 false 12 5.542,2.146 6,2.344 0.458,0.198 10 false STP 3.76,1.906 4.219,2.104 0.458,0.198 10 false 2 3.563,2.135 4.021,2.333 0.458,0.198 10 false L 1.823,1.583 2.281,1.781 0.458,0.198 10 false 1 1.99,1.781 2.448,1.979 0.458,0.198 10 false B 1.823,2.406 2.281,2.604 0.458,0.198 10 false 3 1.979,2.615 2.438,2.813 0.458,0.198 10 false GND 1.979,3.052 2.438,3.25 0.458,0.198 10 false A46 1.969,3.229 3.958,3.5 1.99,0.271 10 false Stop Light Switch Assembly 1.073,1.854 1.531,2.052 0.458,0.198 10 false STOP 1.042,1.563 1.5,1.76 0.458,0.198 10 false 1 1.396,1.563 1.854,1.76 0.458,0.198 10 false 2 1.885,0.448 3.479,0.646 1.594,0.198 10 false from Auxiliary Battery 0.813,4.104 2.604,4.323 1.792,0.219 10 false : Open Detection Area

w/o Canister Pump Module:
C345757E03
5.542,1.26 6.156,1.458 0.615,0.198 10 false STP2 5.521,2.26 6.135,2.458 0.615,0.198 10 false STPO 5.542,3.354 6.156,3.552 0.615,0.198 10 false STP 5.281,3.115 5.896,3.313 0.615,0.198 10 false 12 5.281,2.021 5.896,2.219 0.615,0.198 10 false 22 5.281,1.031 5.896,1.229 0.615,0.198 10 false 37 5.083,3.948 5.698,4.146 0.615,0.198 10 false A41 5.073,4.104 7.135,4.479 2.063,0.375 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.073,4.219 4.885,4.573 0.813,0.354 10 false to Stop Light Circuit 3.75,1.031 4.365,1.229 0.615,0.198 10 false 3 3.771,2.021 4.385,2.219 0.615,0.198 10 false 4 3.781,3.115 4.396,3.313 0.615,0.198 10 false 1 3.396,3.365 4.01,3.563 0.615,0.198 10 false OUT 3.396,2.26 4.01,2.458 0.615,0.198 10 false ACC 3.573,1.281 3.76,1.5 0.188,0.219 10 false L 1.813,1.385 2.104,1.615 0.292,0.229 10 false 7 2,1.615 2.271,1.906 0.271,0.292 10 false B 1.802,3.115 2.052,3.313 0.25,0.198 10 false 2 1.99,3.354 2.604,3.552 0.615,0.198 10 false GND 2.073,3.802 2.385,4.021 0.313,0.219 10 false A47 2.063,3.969 3.854,4.177 1.792,0.208 10 false Stop Light Switch Assembly 0.615,4.365 2.083,4.573 1.469,0.208 10 false : Open Detection Area 1.094,1.667 1.531,1.865 0.438,0.198 10 false STOP 1.031,1.396 1.208,1.594 0.177,0.198 10 false 1 1.406,1.396 1.615,1.563 0.208,0.167 10 false 2 1.865,0.281 3.302,0.5 1.438,0.219 10 false form Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

b.

Check that the stop light switch assembly display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C343117C25
0.375,0.792 0.75,1.042 0.375,0.25 2.271,1.604 2.385,0.948 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 0.448,0.823 0.833,1.042 0.385,0.219 10 false A41 2.354,0.781 2.792,1.01 0.438,0.229 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-12 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V
A41-12 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C343117C25
0.375,0.792 0.75,1.042 0.375,0.25 2.271,1.604 2.385,0.948 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 0.448,0.823 0.833,1.042 0.385,0.219 10 false A41 2.354,0.781 2.792,1.01 0.438,0.229 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A41-12 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V
A41-12 (STP) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the A41 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch off.


d.

Turn the power switch on (READY).


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake booster with master cylinder assembly).

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for LHD)>REMOVAL

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER(for RHD)>REMOVAL




A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)