Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM
RM3210E _59 Vehicle Exterior _047506 MIRROR (EXT) _0245159 POWER MIRROR CONTROL SYSTEM J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM  AUTO Power Retract Mirrors do not operate  


DESCRIPTION

The outer mirror switch assembly sends a mirror auto retract/return signal to the main body ECU (multiplex network body ECU) when the retractable outer mirror switch on the outer mirror switch assembly is in the AUTO position. The main body ECU (multiplex network body ECU) retracts or returns the outer rear view mirror assemblies based on the lock/unlock signal of each door while the power switch is off.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



PROCEDURE

1.CHECK POWER RETRACT MIRROR FUNCTION
a.

Check the power retract mirror function.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM>OPERATION CHECK

OK:

Power retract mirror function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Retractable Mirrors do not Operate with Power Retract Mirror Switch)

2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

Check the power door lock control system.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Power door lock control system is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM

NG

3.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock control system.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Wireless door lock control system is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK ENTRY AND START SYSTEM (for Entry Function)

NG

4.CHECK ENTRY AND START SYSTEM (for Entry Function)
a.

Check the entry and start system (for Entry Function).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry and start system (for Entry Function) is normal.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mirror SW Retractable outer mirror switch signal OFF or ON OFF: Mirror retract switch not in auto position
ON: Mirror retract switch in auto position
-
Body Electrical > Main Body > Data List
Tester Display
Auto Mirror SW
50003 123 105
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
6.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the I11*1 or J10*2 outer mirror switch assembly.

*1: for RHD

*2: for LHD



b.

Disconnect the F18 main body ECU (multiplex network body ECU).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
I11-2 (MAT) - F18-15 (RTR) Always Below 1 Ω
I11-2 (MAT) or F18-15 (RTR) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
J10-4 (MAT) - F18-15 (RTR) Always Below 1 Ω
J10-4 (MAT) or F18-15 (RTR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR