Home › Vehicle Exterior › DOOR / HATCH › FUEL LID OPENER SYSTEM
RM3210E _59 Vehicle Exterior _047505 DOOR / HATCH _0246084 FUEL LID OPENER SYSTEM J

DOOR / HATCH  FUEL LID OPENER SYSTEM  Fuel Lid Opener does not Operate  


DESCRIPTION

When the fuel lid opener switch is pushed, a fuel lid opener switch signal is sent to the ECM. The ECM turns on the FUEL OPN relay and the fuel lid lock with motor assembly opens the fuel lid. When the fuel lid is open, a fuel lid courtesy switch signal is output from the fuel lid lock with motor assembly.

WIRING DIAGRAM

B440785E02
0.083,0.26 1.021,0.656 0.938,0.396 10 false from EFI-MAIN Relay 0.083,0.833 0.938,1.25 0.854,0.417 10 false from Auxiliary Battery 1.604,0.531 2.354,0.854 0.75,0.323 10 false EFI NO. 2 1.573,0.969 2.365,1.302 0.792,0.333 10 false FUEL OPN 2.417,0.625 3.167,0.948 0.75,0.323 10 false 7 2.385,0.177 3.135,0.5 0.75,0.323 10 false 30 2.396,0.385 3.146,0.708 0.75,0.323 10 false 3F 2.167,1.635 4.854,2.146 2.688,0.51 10 false Instrument Panel Junction Block Assembly 4.365,0.823 5.115,1.146 0.75,0.323 10 false 3H 4.365,0.625 5.115,0.948 0.75,0.323 10 false 28 4.365,0.188 5.115,0.51 0.75,0.323 10 false 20 5.271,0.271 6.021,0.594 0.75,0.323 10 false 59 5.542,0.385 6.292,0.708 0.75,0.323 10 false FREL 5.542,3.344 6.292,3.667 0.75,0.323 10 false LIDO 5.542,4.74 6.292,5.063 0.75,0.323 10 false FUEL 5.281,4.625 6.031,4.948 0.75,0.323 10 false 42 5.219,3.229 5.969,3.552 0.75,0.323 10 false 43* 4.302,2.615 5.052,2.938 0.75,0.323 10 false 1 4.333,3.24 5.083,3.563 0.75,0.323 10 false 3* 4.094,2.625 4.844,2.948 0.75,0.323 10 false B 2.74,3.229 3.49,3.552 0.75,0.323 10 false E 2.542,3.229 3.292,3.552 0.75,0.323 10 false 2 2.479,3.656 3.229,3.979 0.75,0.323 10 false M32 2.479,3.823 4.75,4.281 2.271,0.458 10 false Fuel Lid Lock with Motor Assembly 3.771,4.625 4.521,4.948 0.75,0.323 10 false IG 4.021,4.615 4.771,4.938 0.75,0.323 10 false 4 2.677,5.042 3.427,5.365 0.75,0.323 10 false F28 2.677,5.198 4.219,5.594 1.542,0.396 10 false Fuel Lid Opener Switch 5.625,5.292 6.375,5.615 0.75,0.323 10 false A40 5.948,5.292 6.698,5.615 0.75,0.323 10 false ECM 3.115,1.104 3.906,1.438 0.792,0.333 10 false FUEL OPN 2.385,0.823 3.135,1.146 0.75,0.323 10 false 3F 4.365,0.385 5.115,0.708 0.75,0.323 10 false 3F 4.104,3.24 4.854,3.563 0.75,0.323 10 false B 2.927,4.625 3.677,4.948 0.75,0.323 10 false E 2.729,4.625 3.479,4.948 0.75,0.323 10 false 1 0.167,5.417 2.448,5.823 2.281,0.406 10 false *: w/ Canister Pump Module

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Canister Pump Module A
w/o Canister Pump Module B



A

2.PERFORM ACTIVE TEST USING GTS (Activate the Fuel Filler Opener)

B

15.READ VALUE USING GTS (Fuel Lid SW)
2.PERFORM ACTIVE TEST USING GTS (Activate the Fuel Filler Opener)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Fuel Filler Opener Fuel lid lock with motor assembly OFF or ON -
Powertrain > Engine > Active Test
Tester Display
Activate the Fuel Filler Opener
50004 372 41
OK:

The fuel lid lock with motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Fuel Lid SW)

NG

9.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
3.READ VALUE USING GTS (Fuel Lid SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Lid SW Fuel lid opener switch status Close or Open Close: Fuel lid opener switch not pushed
Open: Fuel lid opener switch pushed
-
Powertrain > Engine > Data List
Tester Display
Fuel Lid SW
50003 372 37
OK:

The GTS display changes correctly in response to the operation of the fuel lid opener switch.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (Fuel Lid Sensor SW)

NG

7.INSPECT FUEL LID OPENER SWITCH
4.READ VALUE USING GTS (Fuel Lid Sensor SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Lid Sensor SW Fuel lid courtesy switch status Close or Open Close: Fuel lid closed
Open: Fuel lid open
-
Powertrain > Engine > Data List
Tester Display
Fuel Lid Sensor SW
50003 372 38
OK:

The GTS display changes correctly in response to the operation of the fuel lid courtesy switch (fuel lid lock with motor assembly).



Result:
Proceed to
OK
NG



OK

NG

5.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
5.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
a.

Remove the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>REMOVAL


b.

Inspect the fuel lid lock with motor assembly (fuel lid courtesy switch).

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the A40 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-3 (B) - A40-43 (LIDO) Always Below 1 Ω
M32-3 (B) or A40-43 (LIDO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL LID OPENER SWITCH
a.

Remove the fuel lid opener switch.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SWITCH>REMOVAL


b.

Inspect the fuel lid opener switch.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)

NG

REPLACE FUEL LID OPENER SWITCH

8.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)
a.

Disconnect the A40 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F28-4 (IG) - A40-42 (FUEL) Always Below 1 Ω
F28-1 (E) - Body ground Always Below 1 Ω
F28-4 (IG) or A40-42 (FUEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
a.

Remove the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>REMOVAL


b.

Inspect the fuel lid lock with motor assembly (motor operation).

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.
B429545C04
1.479,0.083 1.906,0.323 0.427,0.24 1.615,0.125 1.927,0.323 0.313,0.198 10 false 3F 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-7 - Body ground Power switch off 11 to 14 V
3F-30 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the A40 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-20 - A40-59 (FREL) Always Below 1 Ω
3F-20 or A40-59 (FREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)
a.

Disconnect the 3H instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3H-28 - M32-1 (B) Always Below 1 Ω
3H-28 or M32-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK FUEL LID OPEN OPERATION
14.CHECK FUEL LID OPEN OPERATION
a.

Check that the fuel lid can be opened.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SYSTEM>OPERATION CHECK

OK:

The fuel lid can be opened.



Result:
Proceed to
OK
NG



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

15.READ VALUE USING GTS (Fuel Lid SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Lid SW Fuel lid opener switch status Close or Open Close: Fuel lid opener switch not pushed
Open: Fuel lid opener switch pushed
-
Powertrain > Engine > Data List
Tester Display
Fuel Lid SW
50003 372 37
OK:

The GTS display changes correctly in response to the operation of the fuel lid opener switch.



Result:
Proceed to
OK
NG



OK

16.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY

NG

23.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)
16.INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
a.

Remove the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>REMOVAL


b.

Inspect the fuel lid lock with motor assembly.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER MOTOR ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - BODY GROUND)

NG

REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-2 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL LID LOCK WITH MOTOR ASSEMBLY)
a.

Disconnect the 3H instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3H-28 - M32-1 (B) Always Below 1 Ω
3H-28 or M32-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - AUXILIARY BATTERY)
a.
B429545C05
1.479,0.083 1.906,0.323 0.427,0.24 1.615,0.125 1.927,0.323 0.313,0.198 10 false 3F 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-30 - Body ground Power switch off 11 to 14 V
3F-7 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the A40 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-20 - A40-59 (FREL) Always Below 1 Ω
3F-20 or A40-59(FREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

21.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Replace the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

22.CHECK FUEL LID OPEN OPERATION
22.CHECK FUEL LID OPEN OPERATION
a.

Check that the fuel lid can be opened.

Click hereVehicle Exterior>DOOR / HATCH>FUEL LID OPENER SYSTEM>OPERATION CHECK

OK:

The fuel lid can be opened.



Result:
Proceed to
OK
NG



OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)

NG

23.CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)
a.

Disconnect the F28 fuel lid opener switch connector.


b.

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F28-4 (IG) - A40-42(FUEL) Always Below 1 Ω
F28-4 (IG) or A40-42 (FUEL) - Body ground Always 10 kΩ or higher
F28-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FUEL LID OPENER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR