Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U029A87  Lost Communication with Hybrid/EV Battery Sensor Module Missing Message  


DESCRIPTION

The battery voltage sensor detects the HV battery conditions (voltage, current and temperature) and the battery cooling fan frequency, and sends the detected signals to the hybrid vehicle control ECU via serial communication. (The hybrid vehicle control ECU does not send signals to the battery voltage sensor.)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U029A87 Lost Communication with Hybrid/EV Battery Sensor Module Missing Message Serial communication error between the hybrid vehicle control ECU and battery voltage sensor: The hybrid vehicle control ECU cannot receive signals from the battery voltage sensor correctly.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

Battery voltage sensor

·

Wire harness or connector


Comes on Master Warning Light:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

With power switch on (IG) and wait for 2 minutes or more.

7.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

8.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AFC00.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AFC00

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check and record any HV system DTCs and freeze frame data. Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only U029A87 is output. A
DTCs other than U029A87 are also output. B



e.

Turn the power switch off.



A

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)

B

2.CHECK BATTERY VOLTAGE SENSOR (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A368051C23
2.167,0.156 2.604,0.385 0.438,0.229 1.938,1.698 2.49,0.958 true 2.938,1.563 2.5,0.875 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 2.26,0.177 2.656,0.49 0.396,0.313 10 false M35 1.781,1.729 2.115,1.99 0.333,0.26 10 false GND 2.885,1.625 3.219,1.885 0.333,0.26 10 false IGCT
*a Component with harness connected
(Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M35-1 (IGCT) - M35-5 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.


HINT:

As there might be an intermittent malfunction in the battery voltage sensor power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




f.

Turn the power switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY VOLTAGE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY VOLTAGE SENSOR POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY VOLTAGE SENSOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the F2 hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery voltage sensor is not loose or disconnected.




c.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


d.

Disconnect the M35 battery voltage sensor connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




e.
A369914C05
1.531,0.177 1.938,0.458 0.406,0.281 1.688,3.969 2.094,4.25 0.406,0.281 2.344,1.875 1.792,1.583 true 1.635,1.583 1.188,1.927 true 2.896,3.677 2.521,4.063 true 1.74,3.677 2.427,4.063 true 0.26,0.083 0.76,0.521 0.5,0.438 10 false *a 0.333,2.083 0.698,2.677 0.365,0.594 10 false *b 1.635,0.229 2.198,0.875 0.563,0.646 10 false F2 1.781,4.01 2.208,4.573 0.427,0.563 10 false M35 0.781,1.854 1.146,2.448 0.365,0.594 10 false BTH+ 2.417,1.833 2.781,2.427 0.365,0.594 10 false BTH- 1.406,3.583 1.854,4.198 0.448,0.615 10 false BTH- 2.948,3.573 3.313,4.167 0.365,0.594 10 false BTH+
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-41 (BTH+) - M35-2 (BTH+) Power switch off Below 1 Ω
F2-42 (BTH-) - M35-3 (BTH-) Power switch off Below 1 Ω
M35-2 (BTH+) - Other terminals and body ground Power switch off 10 kΩ or higher
M35-3 (BTH-) - Other terminals and body ground Power switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery voltage sensor and hybrid vehicle control ECU is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the power switch on (IG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F2-41 (BTH+) - Body ground Power switch on (IG) Below 1 V
F2-42 (BTH-) - Body ground Power switch on (IG) Below 1 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the M35 battery voltage sensor connector.


l.

Install the No. 1 hybrid battery exhaust duct.


m.

Reconnect the F2 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Disconnect the M35 battery voltage sensor connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
A368049C05
2.813,2 3.25,2.281 0.438,0.281 2.094,1.823 2.5,2.219 true 1.885,2.792 2.583,2.313 true 1.833,2.219 2.385,2.219 true 2.885,2.042 3.281,2.417 0.396,0.375 10 false M35 0.146,0.063 0.5,0.479 0.354,0.417 10 false *a 1.656,1.729 2.052,2.104 0.396,0.375 10 false BTH+ 1.552,2.76 1.948,3.135 0.396,0.375 10 false GND 1.448,2.115 1.844,2.49 0.396,0.375 10 false BTH-
*a Rear view of wire harness connector
(to Battery Voltage Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M35-2 (BTH+) - M35-5 (GND) Power switch on (IG) 2.3 to 2.7 V
M35-3 (BTH-) - M35-5 (GND) Power switch on (IG) 2.3 to 2.7 V


NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the power switch is turned on (IG) with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M35-2 (BTH+) - M35-3 (BTH-) Power switch off 4.4 to 5.4 kΩ


HINT:

The resistance will be 2.0 kΩ or less if there is an internal short in the hybrid vehicle control ECU.



j.

Reconnect the M35 battery voltage sensor connector.


k.

Install the No. 1 hybrid battery exhaust duct.


Result:
Proceed to
OK
NG



OK

NG