The radio and display receiver assembly and telephone microphone assembly*1 or map light assembly (telephone microphone assembly)*2 are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Telephone microphone assembly*1 ·
Map light assembly (telephone microphone assembly)*2 ·
Telematics transceiver*3 ·
Radio and display receiver assembly ·
Harness or connector |
*1: w/o Sliding Roof
*2: w/ Sliding Roof
*3: w/ Manual (SOS) Switch
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK
(w/ Manual (SOS) Switch and w/ Sliding Roof) |
A |
| OK
(w/ Manual (SOS) Switch and w/o Sliding Roof) |
B |
| OK
(w/o Manual (SOS) Switch and w/ Sliding Roof) |
C |
| OK
(w/o Manual (SOS) Switch and w/o Sliding Roof) |
D |
| NG | E |
A
B
C
D
E
Disconnect the F36 telematics transceiver connector.
Disconnect the O4 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F36-35 (MCI-) - O4-15 (MCO-) | Always | Below 1 Ω |
| F36-35 (MCI-) or O4-15 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the F36 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-19 (MIN-) - F36-19 (MCO-) | Always | Below 1 Ω |
| F31-19 (MIN-) or F36-19 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O4 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O4-14 (SNS2) | Always | Below 1 Ω |
| F31-6 (SNS2) or O4-14 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F36 telematics transceiver connector.
Disconnect the O2 telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F36-35 (MCI-) - O2-4 (MCO-) | Always | Below 1 Ω |
| F36-35 (MCI-) or O2-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the F36 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-19 (MIN-) - F36-19 (MCO-) | Always | Below 1 Ω |
| F31-19 (MIN-) or F36-19 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O2 telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O2-3 (SNS2) | Always | Below 1 Ω |
| F31-6 (SNS2) or O2-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F36-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O4 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O4-14 (SNS2) | Always | Below 1 Ω |
| F31-19 (MIN-) - O4-15 (MCO-) | Always | Below 1 Ω |
| F31-6 (SNS2) or O4-14 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F31-19 (MIN-) or O4-15 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 14 (SNS2) - 15 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F31 radio and display receiver assembly connector.
Disconnect the O2 telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-6 (SNS2) - O2-3 (SNS2) | Always | Below 1 Ω |
| F31-19 (MIN-) - O2-4 (MCO-) | Always | Below 1 Ω |
| F31-6 (SNS2) or O2-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F31-19 (MIN-) or O2-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
| *a | Component without harness connected
(Telephone Microphone Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG