Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.08
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0236932 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter assembly (meter circuit plate) receives text data signals from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.

Based on these signals, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly (meter circuit plate) cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN Diagnosis Condition:
·

A registration information signal was received from the Navigation receiver assembly*1 or Radio and display receiver assembly*2 when ACC power source voltage was received by the Navigation receiver assembly*1 or Radio and display receiver assembly*2.

·

The power switch is on (IG).

·

IG power source voltage is 9.5 V or more.


Malfunction Status:

The registration information signal is not received from the Navigation receiver assembly*1 or Radio and display receiver assembly*2.


Malfunction Time:

30 seconds or more


·

Harness or connector

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Combination meter assembly (Meter circuit plate)


DTC stored -

*1: for Navigation Receiver Type

*2: for Radio and Display Type


WIRING DIAGRAM

w/ Navigation System


E331962E05
2.396,0.521 2.854,0.719 0.458,0.198 10 false F34 2.396,1.26 2.854,1.458 0.458,0.198 10 false F34 2.802,1.26 3.26,1.458 0.458,0.198 10 false F95 2.802,0.521 3.26,0.719 0.458,0.198 10 false F95 5.01,0.375 5.469,0.573 0.458,0.198 10 false 33 5.01,1.115 5.469,1.313 0.458,0.198 10 false 34 4.948,1.594 5.406,1.792 0.458,0.198 10 false F6 5.26,0.5 5.719,0.698 0.458,0.198 10 false MSCH 5.271,1.24 5.729,1.438 0.458,0.198 10 false MSCL 1.896,0.521 2.281,0.719 0.385,0.198 10 false CNH1 1.927,1.24 2.302,1.438 0.375,0.198 10 false CNL1 0.948,2.354 3.031,2.625 2.083,0.271 10 false : Local Bus Communication Line 4.948,1.75 6.802,2.104 1.854,0.354 10 false Combination Meter Assembly (Meter Circuit Plate) 2.469,0.323 2.927,0.521 0.458,0.198 10 false 3 2.865,0.313 3.323,0.51 0.458,0.198 10 false 3 2.438,0.719 2.896,0.917 0.458,0.198 10 false *1 2.844,0.719 3.302,0.917 0.458,0.198 10 false *2 2.469,1.052 2.927,1.25 0.458,0.198 10 false 4 2.885,1.052 3.344,1.25 0.458,0.198 10 false 4 2.448,1.458 2.906,1.656 0.458,0.198 10 false *1 2.854,1.458 3.313,1.656 0.458,0.198 10 false *2 3.063,2.146 5.167,2.365 2.104,0.219 10 false *1: for Radio and Display Type 3.073,2.448 5.26,2.625 2.188,0.177 10 false *2: for Navigation Receiver Type 0.75,1.729 3.25,1.917 2.5,0.188 10 false Radio and Display Receiver Assembly*1 0.75,2 2.792,2.208 2.042,0.208 10 false Navigation Receiver Assembly*2


w/o Navigation System


E274272E84
2.229,0.573 2.417,0.74 0.188,0.167 10 false 3 4.885,0.563 5.115,0.76 0.229,0.198 10 false 33 4.604,1.563 4.938,1.813 0.333,0.25 10 false F6 0.75,1.583 1.115,1.781 0.365,0.198 10 false F34 1.76,0.74 2.177,0.906 0.417,0.167 10 false CNH1 5.115,0.698 5.677,0.917 0.563,0.219 10 false MSCH 5.115,1.25 5.583,1.469 0.469,0.219 10 false MSCL 2.229,1.135 2.417,1.313 0.188,0.177 10 false 4 4.885,1.125 5.104,1.323 0.219,0.198 10 false 34 0.958,2.365 3.104,2.635 2.146,0.271 10 false : Local Bus Communication Line 1.771,1.302 2.188,1.469 0.417,0.167 10 false CNL1 0.74,1.75 3.271,2.094 2.531,0.344 10 false Radio and Display Receiver Assembly 4.604,1.729 6.438,2.24 1.833,0.51 10 false Combination Meter Assembly (Meter Circuit Plate)


CAUTION / NOTICE / HINT

HINT:

DTC B150A may be stored if the auxiliary battery voltage dropped.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

2.CHECK FOR DTC

B

5.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check if navigation system DTCs are output.

for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY)

B

GO TO NAVIGATION SYSTEM

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Disconnect the F34 radio and display receiver assembly*1 or F95 navigation receiver assembly*2 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F34-3 (CNH1)*1 Always Below 1 Ω
F6-34 (MSCL) - F34-4 (CNL1)*1 Always Below 1 Ω
F6-33 (MSCH) or F34-3 (CNH1) - Body ground*1 Always 10 kΩ or higher
F6-34 (MSCL) or F34-4 (CNL1) - Body ground*1 Always 10 kΩ or higher
F6-33 (MSCH) - F95-3 (CNH1)*2 Always Below 1 Ω
F6-34 (MSCL) - F95-4 (CNL1)*2 Always Below 1 Ω
F6-33 (MSCH) or F95-3 (CNH1) - Body ground*2 Always 10 kΩ or higher
F6-34 (MSCL) or F95-4 (CNL1) - Body ground*2 Always 10 kΩ or higher


*1: for Radio and Display Type

*2: for Navigation Receiver Type



Result:
Proceed to
OK
NG



OK

4.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Replace the combination meter assembly (meter circuit plate) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly (meter circuit plate) and navigation receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output (for Radio and Display Type). B
The audio tab does not illuminate and DTC B150A is output (for Navigation Receiver Type). C



A

END

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

5.CHECK FOR DTC
a.

Check if audio and visual system DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Audio and visual system DTCs are not output. A
Audio and visual system DTCs are output. B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE) - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the F6 combination meter assembly (meter circuit plate) connector.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-33 (MSCH) - F34-3 (CNH1) Always Below 1 Ω
F6-34 (MSCL) - F34-4 (CNL1) Always Below 1 Ω
F6-33 (MSCH) or F34-3 (CNH1) - Body ground Always 10 kΩ or higher
F6-34 (MSCL) or F34-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER ASSEMBLY (METER CIRCUIT PLATE)
a.

Replace the combination meter assembly (meter circuit plate) with a new or known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly (meter circuit plate) and radio and display receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B



A

END

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY