2005-2008 RAV4 · Service Manual TRANSMISSION

P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)

Diagnostic trouble codes · Vehicles built from Aug 2007

DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0705
When one of following conditions is met:
(A) Any 2 or more of the P, N, R, D, 3 and 2 input signals are ON simultaneously (2 trip detection logic)
(B) Any 2 or more of the NSW R, D, 3 and 2 input signals are ON simultaneously (2 trip detection logic)
(C) When both conditions below are met (2 trip detection logic)
  1. One of the NSW, P, N or R input signal is ON
  2. One of the 4 or L input signal is ON
(D) All of the NSW, P, N, R, D, 3 and 2 input signals are OFF (2 trip detection logic)
  1. Open or short in park/neutral position switch circuit
  2. Park/Neutral position switch
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is on P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (R, D, 4, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C170738E01

INSPECTION PROCEDURE

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect the intelligent tester to the DLC3.
  4. Turn the ignition switch ON and turn the tester ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
ON or OFF
Shift lever is:
P or N: ON
Except P or N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (R Range)
PNP switch status/
ON or OFF
Shift lever is:
R: ON
Except R: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (P Range)
PNP switch status/
ON or OFF
Shift lever is:
P: ON
Except P: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (N Range)
PNP switch status/
ON or OFF
Shift lever is:
N: ON
Except N: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (4 or D)
PNP switch status/
ON or OFF
Shift lever is:
4 or D: ON
Except 4 or D: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
Shift lever is:
3: ON
Except 3: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (2 Range
PNP switch status/
ON or OFF
Shift lever is:
2 or L: ON
Except 2 or L: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (L Range)
PNP switch status/
ON or OFF
Shift lever is:
L: ON
Except L: OFF
When shift lever position displayed on intelligent tester differs from actual position, adjustment of PNP switch or shift cable may be incorrect

1. CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
C117645E74
  1. Disconnect the park/neutral position switch connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B28-2 (RB) - Body ground
    Ignition Switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (OUTPUT SIGNAL)

  1. C117645E75
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B28-4 (B) - Body ground
    Ignition Switch ON
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    B



B
Go to step 8
A


3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C110340E94
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    4 - 5
    P and N
    Below 1 Ω
    Except P and N
    10 kΩ or higher
    2 - 6
    P
    Below 1 Ω
    Except P
    10 kΩ or higher
    2 - 1
    R
    Below 1 Ω
    Except R
    10 kΩ or higher
    2 - 9
    N
    Below 1 Ω
    Except N
    10 kΩ or higher
    2 - 7
    D
    Below 1 Ω
    Except D
    10 kΩ or higher
    2 - 3
    2
    Below 1 Ω
    Except 2
    10 kΩ or higher
    2 - 8
    L
    Below 1 Ω
    Except L
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
A175191E11
  1. Connect the park/neutral position switch connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    B96-24 (P) - Body ground
    P
    11 to 14 V
    Except P
    Below 1 V
    B96-25 (R) - Body ground
    R
    11 to 14 V*
    Except R
    Below 1 V
    B96-27 (N) - Body ground
    N
    11 to 14 V
    Except N
    Below 1 V
    B96-26 (D) - Body ground
    D or 4
    11 to 14 V
    Except D or 4
    Below 1 V
    B96-29 (3) - Body ground
    3
    11 to 14 V
    Except 3
    Below 1 V
    B96-28 (2) - Body ground
    2 or L
    11 to 14 V
    Except 2 or L
    Below 1 V

    HINT:
    *: The voltage will drop slightly due to the illumination of the back-up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL UNIT)

  1. A175192E02
    Disconnect the transmission control switch connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    1 (NSSD) - Body ground
    D and 4
    11 to 14 V
    Except D and 4
    Below 1 V
    5 (NSSL) - Body ground
    2 and L
    11 to 14 V
    Except 2 and L
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

  1. A175176E03
    Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    1 (NSSD) - 2 (AT4)
    Except 4 and 3
    10 kΩ or higher
    4 and 3
    Below 1 Ω
    5 (NSSL) - 6 (ATL)
    Except L
    10 kΩ or higher
    L
    Below 1 Ω



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

  1. A175177E02
    Connect the transmission control switch connector.

  1. Disconnect the ECM connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Lever Position
    Specified Condition
    A12-25 (4) - Body ground
    4
    11 to 14 V
    Except 4
    Below 1 V
    A12-26 (L) - Body ground
    L
    11 to 14 V
    Except L
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)

8. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

  1. C162103E09
    Turn the ignition switch OFF.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B28-4 (B) - B96-62 (NSW)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B28-4 (B) or B96-62 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2007)P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (from Aug 2007) →