2005-2008 RAV4 · Service Manual BRAKE

C0200/31 Right Front Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.
Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1271/71, C1272/72, C1275/75/75 and C1276/76 are output only in the test mode.
C115116E02
DTC No.
DTC Detection Condition
Trouble Area
C0200/31
C0205/32
When one of following conditions is met:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1235/35
C1236/36
When either of following is detected:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise continues for 5 seconds or more in sensor signal from abnormal wheel.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
C1271/71
C1272/72
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1275/75
C1276/76
Detected only during test mode.
  1. Front speed sensor
  2. Front speed sensor circuit
  3. Sensor installation

HINT:
  1. DTCs C0200/31 and C1235/35 relate to the front speed sensor RH.
  2. DTCs C0205/32 and C1236/36 relate to the front speed sensor LH.


WIRING DIAGRAM

C136041E01

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    FR Speed Open
    FR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    FL Speed Open
    FL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal

    OK:
    There are no momentary interruptions.

    HINT:
    Perform the above inspection before removing the sensor and connector.



NG
CHECK AND REPAIR HARNESS AND CONNECTOR (SPEED SENSOR CIRCUIT)
OK


2. READ VALUE USING DATA LIST (FRONT SPEED SENSOR)
  1. Check the Data List for proper functioning of the front speed sensor.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    FR Wheel Speed
    Wheel speed sensor (FR) reading: Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph)
    Similar to speed indicated on speedometer
    FL Wheel Speed
    Wheel speed sensor (FL) reading: Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph)
    Similar to speed indicated on speedometer

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +-10% in the speedometer indication.



NG
Go to step 5
OK


3. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a test mode inspection and check for DTCs (Click here).

    OK:
    No DTC output.



NG
CHECK AND REPAIR HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


4. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 10
A

END

5. INSPECT FRONT SPEED SENSOR (INSTALLATION)

  1. C108871E03
    Check that the speed sensor installation bolt is tightened properly.

    OK:
    The installation bolt is tightened properly, and there is no clearance between the sensor and front steering knuckle.

Torque:
8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

HINT:
If the installation portion of the sensor is dirty, clean it and reinstall the sensor.
Check the speed sensor after the speed sensor replacement (Click here).



NG
TIGHTEN BOLT PROPERLY OR REPLACE FRONT SPEED SENSOR
OK


6. CHECK SPEED SENSOR (TIP)
  1. Remove the front speed sensor.

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    HINT:
    Check the speed sensor signal after cleaning or replacing the speed sensor (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7. CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR)

  1. C117857E04
    Disconnect the A27 ECU connector.

  1. Disconnect the A61 and A62 sensor connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH:
    Tester Connection
    Specified Condition
    A27-9 (FL+) - A61-2 (FL+)
    Below 1 Ω
    A27-8 (FL-) - A61-1 (FL-)
    Below 1 Ω
    A27-9 (FL+) - Body ground
    10 kΩ or higher
    A27-8 (FL-) - Body ground
    10 kΩ or higher
    for RH:
    Tester Connection
    Specified Condition
    A27-31 (FR+) - A62-2 (FR+)
    Below 1 Ω
    A27-30 (FR-) - A62-1 (FR-)
    Below 1 Ω
    A27-31 (FR+) - Body ground
    10 kΩ or higher
    A27-30 (FR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK SKID CONTROL ECU (SENSOR INPUT VOLTAGE)

  1. C126292E01
    Disconnect the A61 and A62 sensor connectors.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A61-2 (FL+) - Body ground
    Ignition switch on (IG)
    5.7 to 17.3 V
    A62-2 (FR+) - Body ground
    Ignition switch on (IG)
    5.7 to 17.3 V



NG
REPLACE BRAKE ACTUATOR ASSEMBLY
OK


9. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A


10. REPLACE FRONT SPEED SENSOR
  1. Replace the front speed sensor.


NEXT


11. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2008)C0200/31 Right Front Wheel Speed Sensor Signal (+ 7 more codes) (Jan 2007 – Jul 2007) →