C0200/31 Right Front Wheel Speed Sensor Signal
Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007
Also covers:
- C0205/32 Left Front Wheel Speed Sensor Signal
- C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH
- C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH
- C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.
The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.
DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1271/71, C1272/72, C1275/75/75 and C1276/76 are output only in the test mode.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| C0200/31 C0205/32 |
When one of following conditions is met:
|
|
| C1235/35 C1236/36 |
When either of following is detected:
|
|
| C1271/71 C1272/72 |
Detected only during test mode. |
|
| C1275/75 C1276/76 |
Detected only during test mode. |
|
- HINT:
- DTCs C0200/31 and C1235/35 relate to the front speed sensor RH.
- DTCs C0205/32 and C1236/36 relate to the front speed sensor LH.
- DTCs C0200/31 and C1235/35 relate to the front speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Check the speed sensor signal in test mode after cleaning or replacement (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).
Skid control ECU Item (Display)
Measurement Item / Range (Display)
Normal Condition
FR Speed Open
FR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
FL Speed Open
FL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
- OK:
- There are no momentary interruptions.
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING DATA LIST (FRONT SPEED SENSOR) |
Check the Data List for proper functioning of the front speed sensor.
Skid control ECU Item (Display)
Measurement Item / Range (Display)
Normal Condition
FR Wheel Speed
Wheel speed sensor (FR) reading: Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph)
Similar to speed indicated on speedometer
FL Wheel Speed
Wheel speed sensor (FL) reading: Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph)
Similar to speed indicated on speedometer
- OK:
- There is almost no difference between actual wheel speed and displayed speed value.
- HINT:
- There is a tolerance of +-10% in the speedometer indication.
|
|
||||
| OK | |
| 3. PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Perform a test mode inspection and check for DTCs (Click here).
- OK:
- No DTC output.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 5. INSPECT FRONT SPEED SENSOR (INSTALLATION) |
Check that the speed sensor installation bolt is tightened properly.

- OK:
- The installation bolt is tightened properly, and there is no clearance between the sensor and front steering knuckle.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
- HINT:
- If the installation portion of the sensor is dirty, clean it and reinstall the sensor.
- Check the speed sensor after the speed sensor replacement (Click here).
|
|
||||
| OK | |
| 6. CHECK SPEED SENSOR (TIP) |
Remove the front speed sensor.
Check the sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- HINT:
- Check the speed sensor signal after cleaning or replacing the speed sensor (Click here).
|
|
||||
| OK | |
| 7. CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Disconnect the A27 ECU connector.

Disconnect the A61 and A62 sensor connectors.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
- for LH:
Tester Connection
Specified Condition
A27-9 (FL+) - A61-2 (FL+)
Below 1 Ω
A27-8 (FL-) - A61-1 (FL-)
Below 1 Ω
A27-9 (FL+) - Body ground
10 kΩ or higher
A27-8 (FL-) - Body ground
10 kΩ or higher
- for RH:
Tester Connection
Specified Condition
A27-31 (FR+) - A62-2 (FR+)
Below 1 Ω
A27-30 (FR-) - A62-1 (FR-)
Below 1 Ω
A27-31 (FR+) - Body ground
10 kΩ or higher
A27-30 (FR-) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK SKID CONTROL ECU (SENSOR INPUT VOLTAGE) |
Disconnect the A61 and A62 sensor connectors.

Measure the voltage of the wire harness side connectors.
- Standard voltage:
Tester Connection
Condition
Specified Condition
A61-2 (FL+) - Body ground
Ignition switch on (IG)
5.7 to 17.3 V
A62-2 (FR+) - Body ground
Ignition switch on (IG)
5.7 to 17.3 V
|
|
||||
| OK | |
| 9. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | |
| 10. REPLACE FRONT SPEED SENSOR |
Replace the front speed sensor.
| NEXT | |
| 11. RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC(s) is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | ||
| ||
