2005-2008 RAV4 · Service Manual BRAKE

C0210/33 Right Rear Wheel Speed Sensor Signal

Diagnostic trouble codes · Vehicles built Nov 2005 – Dec 2006

Also covers:

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008

DESCRIPTION

Refer to DTC C0200/31 (Click here).
DTCs C1273/73, C1274/74, C1277/77 and C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1273/73, C1274/74, C1277/77 and C1278/78 are output only in the test mode.
DTC No.
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When one of following conditions is met:
  1. At vehicle speed of 10 km/h (6 mph) or more, open or short in sensor signal circuit continues for 1 second or more.
  2. Momentary interruption of sensor signal from abnormal wheel occurs 255 times or more.
  3. Open in speed sensor signal circuit continues for 0.5 seconds or more.
  4. With IG1 terminal voltage 9.5 V or more, sensor power supply voltage decreases for 0.5 seconds or more.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1238/38
C1239/39
When either condition below is met:
  1. At vehicle speed of 20 km/h (12 mph) or more, noise in malfunctioning wheel sensor signal condition continues for 5 seconds or more.
  2. At vehicle speed of 10 km/h (6 mph) or more, noise input occurs once per rotor rotation for 15 seconds or more.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
C1273/73
C1274/74
Detected only during test mode.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation

HINT:
  1. DTC C0210/33 and C1238/38 relate to the skid control sensor RH.
  2. DTC C0215/34 and C1239/39 relate to the skid control sensor LH.


WIRING DIAGRAM

C136041E02

INSPECTION PROCEDURE

NOTICE:
Check the speed sensor signal in test mode after cleaning or replacement (Click here).


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness corresponding to a DTC (Click here).

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    RR Speed Open
    RR speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -
    RL Speed Open
    RL speed sensor open detection / ERROR or NORMAL
    ERROR: Momentary interruption
    NORMAL: Normal
    -

    OK:
    There are no momentary interruptions.

    HINT:
    Perform this inspection before removing the sensor and connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)
  1. Check the Data List for proper functioning of the rear speed sensor.

    Skid control ECU 
    Item (Display)
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph)
    Similar to speed indicated on speedometer
    -
    RL Wheel Speed
    Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202.8 mph)
    Similar to speed indicated on speedometer
    -

    OK:
    There is almost no difference between actual wheel speed and displayed speed value.

    HINT:
    There is a tolerance of +-10% in the speedometer indication.



NG
Go to step 5
OK


3. PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTCs output.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 11
A

END

5. INSPECT REAR SPEED SENSOR (INSTALLATION)

  1. C108871E03
    Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and rear axle carrier.

Torque:
8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

HINT:
Check the speed sensor signal after the replacement (Click here).



NG
CHECK AND REPLACE REAR SPEED SENSOR
OK


6. CHECK REAR SPEED SENSOR (TIP)
  1. Remove the rear speed sensor.

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAR OR REPLACE REAR SPEED SENSOR
OK


7. CHECK WIRE HARNESS (SKID CONTROL ECU - REAR SPEED SENSOR)

  1. C136734E01
    Disconnect the A26 ECU connector.

  1. Disconnect K25 and K26 sensor connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH Side:
    Tester Connection
    Specified Condition
    A26-20 (RL+) - K25-1 (RL+)
    Below 1 Ω
    A26-6 (RL-) - K25-2 (RL-)
    Below 1 Ω
    A26-20 (RL+) - Body ground
    10 kΩ or higher
    A26-6 (RL-) - Body ground
    10 kΩ or higher
    for RH Side:
    Tester Connection
    Specified Condition
    A26-5 (RR+) - K26-1 (RR+)
    Below 1 Ω
    A26-19 (RR-) - K26-2 (RR-)
    Below 1 Ω
    A26-5 (RR+) - Body ground
    10 kΩ or higher
    A26-19 (RR-) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK SKID CONTROL ECU (SENSOR INPUT VOLTAGE)

  1. C136735E01
    Disconnect K25 and K26 sensor connectors.

  1. Measure the voltage of the wire harness side connectors.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    K25-1 (RL+) - Body ground
    Ignition switch on (IG)
    5.7 to 17.3 V
    K26-1 (RR+) - Body ground
    Ignition switch on (IG)
    5.7 to 17.3 V



NG
REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY
OK


9. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A


10. REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor.


NEXT


11. RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY


← C0200/31 Right Front Wheel Speed Sensor Signal (+ 7 more codes) (Aug 2007 – Jul 2008)C0210/33 Right Rear Wheel Speed Sensor Signal (+ 7 more codes) (Jan 2007 – Jul 2007) →