2005-2008 RAV4 · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL AIR CONDITIONING UNIT ASSEMBLY

  1. E124545
    Install the A/C unit with the bolt and nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


2. INSTALL INSTRUMENT PANEL REINFORCEMENT

  1. Install the instrument panel reinforcement with the 6 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


    E124270

  1. Install the 3 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


    E124269

  1. Install the 4 bolts and connect the ground wire.

    E124267

  1. Attach the 12 clamps.

    E124268E03


3. INSTALL DRAIN COOLER HOSE

  1. E124266
    Install the drain hose.


4. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E124261E01
    Install the A/C amplifier with the screw.

  1. Connect the connector.

  1. E127015
    Attach the 2 clamps to the amplifier.


5. INSTALL AIR DUCT

  1. E124265
    Attach the 2 claws and install the air duct.


6. INSTALL REAR AIR DUCT

  1. E124272
    Attach the 3 claws and install the air duct rear.

  1. E127179
    Attach the 2 clamps and install the wire harness.


7. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

  1. E124264
    Install the instrument panel brace with the bolt, nut and screw.

  1. E127013E01
    Install the clamp and connect the wire harness.

  1. E127109
    Reposition the floor carpet.


8. INSTALL DEFROSTER NOZZLE ASSEMBLY

  1. E124263
    Attach the 3 claws and install the defroster nozzle assembly lower.


9. INSTALL LOWER INSTRUMENT PANEL
  1. Install the lower instrument panel (Click here).


10. INSTALL UPPER INSTRUMENT PANEL
  1. Install the upper instrument panel (Click here).


11. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column (Click here).


12. CONNECT HEATER WATER OUTLET HOSE

  1. H102044
    Connect the water hose and attach the clip.


13. CONNECT HEATER WATER INLET HOSE

HINT:
Use the same procedures described for the water outlet hose.


14. CONNECT TUBE SUB-ASSEMBLY

  1. E127302E01
    Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to new 2 O-rings and the fitting surface of the suction tube and liquid tube.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the suction tube and liquid tube.

  1. Connect the suction tube and liquid tube.

    HINT:
    After the connection, check that the claw of the piping clamp is engaged.

  1. Install the plate with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

16. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).


17. ADD ENGINE COOLANT
For 1AZ-FE and 2AZ-FE, refer to the following procedures (Click here).
For 2AD-FHV and 2AD-FTV, refer to the following procedures (Click here).

18. CHARGE REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    430 +-30 g (15.2 +-1.1 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)

    I037365E02

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.


19. WARM UP ENGINE
  1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch ON after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


20. CHECK FOR ENGINE COOLANT LEAKS
  1. Remove the radiator reservoir cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the radiator reservoir cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. A128571E01
    Fill the radiator with coolant, and then attach a radiator cap tester.

  1. Warm up the engine.

  1. Pump the radiator cap tester to 137 kPa (1.4 kgf/cm2, 19 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leakage.
    If there are no signs of external coolant leaks, check the heater core, cylinder block and head.

  1. Reinstall the radiator cap.


21. CHECK FOR LEAKAGE OF REFRIGERANT
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the gas leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E12
    Using a gas leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and leave the pressure switch on for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.

← REASSEMBLY (from Nov 2005)INSTALLATION (Jan 2007 – Jul 2007) →