VC Output Circuit
Circuit diagnosis · Vehicles built from Aug 2007
DESCRIPTION
The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
- HINT:
- Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned ON. The MIL goes off when the engine is started.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.
- OK:
- MIL lights up.
|
|
||||
| NG | |
| 2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and tester on.
Check the communication between the tester and ECM.
- Result:
Result
Proceed to
Communication is possible
A
Communication is not possible
B
|
|
||||
| B | |
| 3. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle body connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the throttle body connector.
|
|
||||
| B | |
| 4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the accelerator pedal position sensor connector.
|
|
||||
| B | |
| 5. CHECK MIL (BATTERY CURRENT SENSOR) |
Disconnect the battery current sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the battery current sensor connector.
|
|
||||
| B | |
| 6. CHECK MIL (VVT SENSOR FOR BANK 1 INTAKE SIDE) |
Disconnect the VVT sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor connector.
|
|
||||
| B | |
| 7. CHECK MIL (VVT SENSOR FOR BANK 2 INTAKE SIDE) |
Disconnect the VVT sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor connector.
|
|
||||
| B | |
| 8. CHECK MIL (VVT SENSOR FOR BANK 1 EXHAUST SIDE) |
Disconnect the VVT sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor connector.
|
|
||||
| B | |
| 9. CHECK MIL (VVT SENSOR FOR BANK 2 EXHAUST SIDE) |
Disconnect the VVT sensor connector.
Turn the ignition switch to the ON position.
Check the MIL.
- Result:
Result
Proceed to
MIL illuminates
A
MIL does not illuminate
B
Reconnect the VVT sensor connector.
|
|
||||
| B | |
| 10. CHECK WIRE HARNESS |
Disconnect the throttle body connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the battery current sensor connector.
Disconnect the VVT sensor for bank 1 intake side connector.
Disconnect the VVT sensor for bank 2 intake side connector.
Disconnect the VVT sensor for bank 1 exhaust side connector.
Disconnect the VVT sensor for bank 2 exhaust side connector.
Disconnect the ECM connectors.

Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
B96-96 (VCTA) - Body ground
10 kΩ or higher
A12-57 (VCPA) - Body ground
10 kΩ or higher
A12-58 (VCP2) - Body ground
10 kΩ or higher
B96-80 (VCIB) - Body ground
10 kΩ or higher
B96-115 (VCV1) - Body ground
10 kΩ or higher
B96-113 (VCV2) - Body ground
10 kΩ or higher
B96-114 (VCE1) - Body ground
10 kΩ or higher
B96-112 (VCE2) - Body ground
10 kΩ or higher
Reconnect the throttle body connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the battery current sensor connector.
Reconnect the VVT sensor connector.
Reconnect the ECM connectors.
|
|
||||
| OK | ||
| ||
