Fuel Pump Control Circuit
Circuit diagnosis · Vehicles built from Aug 2007
DESCRIPTION
The F/PMP relay switches the fuel pump speed according to the engine conditions. The fuel pump operates when the ECM receives the starter-operating signal (STA) and crankshaft-rotating signal (NE). The F/PMP relay is turned ON while the engine is idling or operating at low load. This causes current to flow through the fuel pump resistor to the fuel pump. The fuel pump then operates at low speed. The F/PMP relay is turned OFF while the engine is cranking or operating at high load. The fuel pump then operates at normal speed.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP/SPD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.
- OK:
- Fuel pump operating sound occurs.
|
|
||||
| NG | |
| 2. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY INPUT VOLTAGE) |
Measure the voltage between the terminal of the instrument panel junction block and the body ground when the ignition switch is turned ON and OFF.

- Standard voltage:
Tester Connection
Ignition Switch Condition
Specified Condition
IB-11 - Body ground
OFF
Below 1 V
IF-4 - Body ground
IB-11 - Body ground
ON
9 to 14 V
IF-4 - Body ground
|
|
||||
| NG | |
| 3. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - INTEGRATION RELAY AND IG2 RELAY) |
![]() ![]() |
Remove the integration relay and IG2 relay from the engine room No. 1 relay block.
Disconnect the instrument panel junction block connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
IG2 relay 5 - IF-4
Below 1 Ω
1A-4 - IB-11
Below 1 Ω
IF-4 - Body ground
10 kΩor higher
IB-11 - Body ground
10 kΩor higher
Reinstall the integration relay and IG2 relay.
Reconnect the instrument panel junction block connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (C/OPN RELAY) |
Remove the instrument panel junction block.

Measure the C/OPN relay resistance.
- Standard resistance:
Tester Connection
Specified Condition
IB-11 - IA-8
10 kΩ or higher
Below 1 Ω
(When battery voltage is applied to terminals IF-4 and IE-5)
- HINT:
- Relay coil circuit between IF-4 and IE-5 is through IGN fuse.
Reinstall the instrument panel junction block.
|
|
||||
| OK | |
| 5. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - ECM) |
Disconnect the ECM connector.

Disconnect the IE connector from the instrument panel junction block.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
IE-5 - A12-7 (FC)
Below 1Ω
IE-5 or A12-7 (FC) - Body ground
10 kΩ or higher
Reconnect the instrument panel junction block and the ECM connectors.
|
|
||||
| OK | |
| 6. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check the operation of the relay while operating it using the intelligent tester.
- OK:
- Operating noise can be heard from the relay.
|
|
||||
| NG | |
| 7. INSPECT F/PMP RELAY |
Inspect the F/PMP relay (Click here).
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (F/PMP RELAY - ECM AND INSTRUMENT PANEL JUNCTION BLOCK) |
![]() ![]() |
Remove the F/PMP relay from the engine room No. 1 relay block.
Disconnect the ECM connector.
Disconnect the IA instrument panel junction block connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
F/PMP relay terminal 1 - B96-59 (FPR)
Below 1 Ω
F/PMP relay terminal 2 - IA-8
Below 1 Ω
F/PMP relay terminal 3 - IA-8
Below 1 Ω
F/PMP relay terminal 1 or B96-59 (FPR) - Body ground
10 kΩ or higher
F/PMP relay terminal 2 or IA-8 - Body ground
10 kΩ or higher
F/PMP relay terminal 3 or IA-8 - Body ground
10 kΩ or higher
Reconnect the ECM connector
Reconnect the instrument panel junction block connector.
Reinstall the F/PMP relay.
|
|
||||
| OK | |
| 9. CHECK WIRE HARNESS (F/PMP - FUEL PUMP AND PUMP RESISTOR) |
![]() ![]() |
Remove the F/PMP relay from the engine room No. 1 relay block.
Disconnect the fuel pump connector.
Disconnect the fuel pump resistor connector.
Measure the resistance.
- Standard resistance:
Tester Connection
Specified Condition
F/PMP relay terminal 4 - T1-4
Below 1 Ω
F/PMP relay terminal 5 - A63-1
Below 1 Ω
A63-2 - T1-4
Below 1 Ω
T1-5 - Body ground
Below 1 Ω
F/PMP relay terminal 4 or T1-4 - Body ground
10 kΩ or higher
F/PMP relay terminal 5 or A63-1 - Body ground
10 kΩ or higher
A63-2 or T1-4 - Body ground
10 kΩ or higher
Reconnect the fuel pump resistor connector.
Reconnect the fuel pump connector.
Reinstall the F/PMP relay.
|
|
||||
| OK | |
| 10. INSPECT FUEL PUMP |
Inspect fuel pump resistance.

Measure the resistance between the terminals.
- Standard resistance:
- 0.2 to 3.0 Ω at 20°C (68°F)
Inspect fuel pump operation.
Apply the battery voltage to both the terminals. Check that the pump operates.
- NOTICE:
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
- Keep the fuel pump as far away from the battery as possible.
- Always turn the voltage on and off on the battery side, not the fuel pump side.
- These tests must be done quickly (within 10 seconds) to prevent the coil from burning out.
|
|
||||
| OK | |
| 11. INSPECT FUEL PUMP RESISTOR |
Measure the resistance of the fuel pump resistor.
- Standard resistance:
- 0.30 to 0.34 Ω at 20°C (68°F)
|
|
||||
| OK | ||
| ||
| 12. READ VALUE USING INTELLIGENT TESTER (STARTER SIG) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned ON and START.
- OK:
Ignition Switch Position
STARTER SIG
ON
OFF
START
ON
|
|
||||
| OK | |
| 13. READ VALUE USING INTELLIGENT TESTER (ENGINE SPD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the tester while cranking.
- Standard:
- Values are displayed continuously.
|
|
||||
| OK | ||
| ||



