INSTALLATION
Removal / installation · Vehicles built Nov 2005 – Jul 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
| 1.
INSTALL REAR BUMPER SIDE MOULDING SUB-ASSEMBLY LH (for Wide Body) |
 |
- Attach the 5 outside moulding retainers to install the moulding.
| 2.
INSTALL REAR BUMPER SIDE MOULDING SUB-ASSEMBLY RH (for Wide Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 3.
INSTALL NO. 1 REAR BUMPER PLATE (for Long Body) |
 |
- Install the bumper plate with the 6 outside moulding retainers.
| 4.
INSTALL REAR BUMPER SIDE RETAINER LH (for Short Body) |
 |
- Install the side retainer with the 2 screws.
| 5.
INSTALL REAR BUMPER SIDE RETAINER RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 6.
INSTALL REAR BUMPER SIDE SUPPORT LH (for Short Body) |
 |
- Attach the claw to install the bumper side support.
Install the screw.
| 7.
INSTALL REAR BUMPER SIDE SUPPORT RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 8.
INSTALL REAR BUMPER SIDE RETAINER LH (for Long Body) |
 |
- Attach the claw to install the side retainer.
Install the screw.
| 9.
INSTALL REAR BUMPER SIDE RETAINER RH (for Long Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 10.
INSTALL REAR BUMPER SIDE SUPPORT LH (for Long Body) |
 |
- Attach the claw to install the bumper side support.
Install the 2 screws.
| 11.
INSTALL REAR BUMPER SIDE SUPPORT RH (for Long Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 12.
INSTALL REAR BUMPER ARM SUPPORT REINFORCEMENT LH (for Short Body) |
 |
- Install the bumper arm support with the 3 bolts.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 13.
INSTALL REAR BUMPER ARM SUPPORT REINFORCEMENT RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 14.
INSTALL REAR BUMPER REINFORCEMENT (for Short Body) |
 |
- Install the bumper reinforcement with the 6 bolts.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 15.
INSTALL REAR BUMPER ABSORBER (for Short Body) |
 |
- Install the absorber.
| 16.
INSTALL REAR BUMPER REINFORCEMENT (for Long Body) |
 |
- Install the bumper reinforcement with the 6 bolts.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 17.
INSTALL REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light) |
 |
- Install the fog light with the 3 bolts.
| 18.
INSTALL REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 19.
INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/ Reflex Reflector) |
 |
- Install the reflex reflector with the screw.
| 20.
INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/ Reflex Reflector) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 21.
INSTALL REAR BUMPER PROTECTOR |
 |
- HINT:
- When removing the double-side tape, heat the rear bumper.
- Standard heating temperature:
Item
|
Specified Condition
|
Rear bumper
|
40 to 60°C (104 to 140°F)
|
Clean the bumper surface.
Using a heat light, heat the bumper surface.
Remove the double-sided tape from the bumper.
Wipe off any tape adhesive residue with cleaner.
- Install the new bumper protector.
| 22.
INSTALL REAR BUMPER COVER |
 |
- Put protective tape under the quarter panel.
w/ License Light:
Install the 2 license plate lights (Click here).
Connect the license plate light connector.
w/ Fog Light:
Connect the 2 fog light connectors.
Attach the 12 claws to install the bumper cover.
- Install the 9 screws and 7 clips.
| 23.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|